Question about Cars & Trucks

1 Answer

I have a 98 hombre 2.2 Manuel I changed the ignition tumbler cause I had no key a lock Smith did it it will start run for about 2 second and shut off. If you wait a few minutes it will start again but shuts off again It has good fuel pressure and a new fuel filter but I can't figure it oit

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

This vehicle needs to have the new ignition switch reprogramed to the vehicle by the dealer as it is a anti theft system so no one can steal the car without the ignition key it shuts down the fuel injectors after a few seconds. good luck.

Posted on Jan 24, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mike258
  • 1498 Answers

SOURCE: 1997 GMC K1500 4x4 5.7 ex.cab SFI injection system

Hey there boatright33,

A few things things immediately come to mind.

There may be a problem with the engine controller. You could check the ODBII onboard diagnostics. Auto part stores will usually do this for you at no cost.

When you pulled the ones that were/went bad, how did the filters look? Could there be particulate matter still in the tank causing them to fail.

I always put this one off until last. Check the injectors. Are they gummed up?

Let me know what you find out
Mike


Posted on Aug 12, 2008

  • 2 Answers

SOURCE: 98 pontiac Sunfire shuts self off

You might not need a tumble, the sys is controled by the key, and transponder, and the ecm. Most auto locks smiths can come out and check the system, might just need a key re-programed

Posted on Nov 14, 2008

motor1258
  • 6674 Answers

SOURCE: fuel pump not staying on 1993 k1500 350

Some GM products also incorporate the oil sender switch into that circuit for fuel pump, so that in case of an accident, engine shuts off, oil pressure drops, in turn, shuts off power to fuel pump. May be worth a look at what your getting for oil pressure, as well as checking switch/sender.

Posted on Feb 13, 2009

  • 99 Answers

SOURCE: Isuzu Hombre pickup, 2.2L Vortec, Won't Start.

You need four things for an engine to run. 1. fuel 2. spark 3. compression 4. timing (spark at the right time. By your post it seems you have fuel and spark and you probably have compression unless you blew a head gasket. That leaves the timing. Check the timing and/or the timing belt or chain whichever you have.

Posted on Aug 07, 2009

  • 409 Answers

SOURCE: 1988 silverado, tbi 350 has 12 psi fuel pressure,

Fuel pressure is a little low, check the pressure regulator, and the fuel filter

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 98 Camry. The ignition switch had been replaced prior to purchase, so there is a different key for the ignition than the doors. Who ever installed the switch tiewrapped the old key to the side of...


I WOULD GO AND GET NEW IGNITION SWITCH THEY TIEWAPPED OLD KID? YA I WOULD SAY START BY REPLACING SWITCH THE RIGHT WAY. THEN IS PROBLUM IS FIXED AND U WANT ONE KEY FOR ALL GO TO A LOCK SMITH SO HE CAN MACH UP TUMBLERS IN SIDE LOCK SO ONE KEY WORKS ALL

Apr 24, 2012 | 1998 Toyota Camry

1 Answer

1998chevy cavalier ignition switch wont let me crank although i am able to insert key in and take out.If i fiddle with it it sometimes lets me turn key to back position,forward just not happening.


your tumblers inside of switch is off not matching your key cut ,this a command prob .you need to have switch replaced ,or have lock smith change tumblers

Jul 25, 2011 | 1998 Chevrolet Cavalier

1 Answer

I have a 2005 Malibu and been having recurring problems with the key not turning in the ignition. It happens about once every two weeks and it's a real pain in the **** because I have to fiddle with it and...


I would replace the ignition cylinder. the tumbler are wearing funny and this is causing the key to not turn or get stuck . I believe you have a pass key system on your car too . so after the cylinder is replace or rebuild you may need to do a relearn with the new lock cylinder. Not sure if you can rebuild the key cylinder and if a lock smith would have the right tumbler codes . but i know for sure if you buy the lock cylinder from a dealership they can code the tumbler to match the original key

Mar 06, 2011 | 2005 Chevrolet Malibu

1 Answer

The key goes in alright but wont turn


get an expert lock smith to recut you a new key the tumblers mite have moved or just change the ignition switch

Jan 07, 2010 | 1994 Chevrolet Cavalier

2 Answers

My key wont turn in the ignition the ignition was jammed by a forein key now the real key wont work


need more info does the key work in the door i am in the process of elimination thanks This is asked to give you the best possible repair

Dec 24, 2009 | 1997 Nissan Sentra

2 Answers

Jammed/locked ignition swith - 2000 Chev Suburban 1500


the tumblers have worn out and not engaeing properly. Repair consists of removeing the ignition switch assembly and installiing a new one. Since it has jammed, mostly a tumbler or two may have broken off in the cylinder houseing also.

Jul 23, 2009 | 2001 Chevrolet Suburban

2 Answers

Ignition won't turn to drive


if tapping it doesnt work. hit it hard for a few minutes then try to turn it forward and back both then repeat.  I had a tow truck come to tow me and he started banging on mine.  I said i already did that while waiting for you and he said you will see.  he kept doing it and a few minutes later i looked like a ********.  He told me the pins were sticking and a lock smith could take the first 2 pins out for me. 

Mar 20, 2009 | 2003 Chrysler 300M

1 Answer

2000 contour


for 98 contour issue. TSB 98-21-14 not covered by warranty

This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar)

Mar 09, 2009 | 2000 Ford Contour

2 Answers

98 pontiac Sunfire shuts self off


You might not need a tumble, the sys is controled by the key, and transponder, and the ecm. Most auto locks smiths can come out and check the system, might just need a key re-programed

Nov 14, 2008 | 2005 Pontiac Sunfire

1 Answer

1997 ford contour


this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14
  • IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED
Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar

Aug 13, 2008 | 1997 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...