Question about 1993 Isuzu Pickup

Open Question

Rebuild engine 1993 isuzu pickup 2.3l

I need to rebuild the engine on an isuzu pickup 2.3L 2 door. I can not find a rebuild manual or anyone that can assist with what to buy and how to go about doing this. Can anyone assist me please? TY

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 651 Answers

SOURCE: Need a vacume diagram

open the hood and see if there is a diagram for vacuum lines on the front rail above the radiator. or under the hood itself.

Posted on Dec 01, 2008

Ad
  • 1 Answer

SOURCE: 1998 Isuzu Trooper Shop Manual

The 1998 Isuzu Trooper is identical to the 1996 & 1997 Troopers with the 3.2L V6 motor. Chilton-Haynes have a decnet and detailed manual for this car. It's available on Amazon.com. That's where I got mine!

Posted on Apr 11, 2009

dmsr63
  • 2050 Answers

SOURCE: 1994 Isuzu Pickup replace rotor, caliper, repack wheel barrings.

Remove caliper, then the caliper bracket that supports the pads and caliper. The rotot should have one or two threaded holes near the lug nut studs. You install a bolt here (Correct thread pitch) and thread it in to "pop" off the rotor. (They are usually rusted on.)
Keep in mind that the new caliper needs to have the brake fluid bled.

Posted on Oct 01, 2009

simontricket
  • 235 Answers

SOURCE: manual for time belt replacemant Isuzu Trooper

4JX1 diesel engine has a belt . 4JGE is a different engine completely. To change it set #1 on tdc fireing stroke using the mark on the back lip of the crank pulley (sit it at 12'oclock) and see the mark on the camshaft bearing matches the notch on the pulley .Ignore the marks on the lower belt pulley.
Tensioner and cover removal/replacement is standard and the chnage period is 60,000 miles.

Posted on Dec 20, 2009

  • 105 Answers

SOURCE: i am rebuilding a 1993 isuzu rodeo transmission

you can go to google, put in the make and year of veichle and problem, should give a lot of sites to where you can find that info, you may go to fords website and find it too

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rebuild carburetor


Purchase a kit for THAT carburetor and all instructions will be in the kit.

Mar 30, 2017 | Isuzu Cars & Trucks

2 Answers

Where is the obd port on my 1993 isuzu Amigo


wow no engine size stated, and MATTERs.!
with no tech1 or 1a scan tooL (real scan tools)
what good is DLC?>
sure jumper CODES< (DTC errors in todays parlance)
there is abs tool.. but only on some cars.

and more. read the FSM yet?
lets pretend you said how do i get the PCM flash error codes
easy jumper the DLC. 'diag, link connector"

google Isuzu DLC jumpers, nets you all this.

http://www.troublecodes.net/isuzu/

there is no world standards for OBD1 so DCL are
every freakn where.

in cab or engine bay or like hondas, on PCM casiing
wild and wolly DLC>


quote

Multi-Port Fuel Injection

Amigo,Trooper II , Rodeo & Pickup
On Rodeo, Amigo, and Pickup (except 1993-95 models W/3.2L engine), connect the single wire diagnostic leads located behind the left hand kick panel together. On 1993-95 Rodeo models W/3.2 engine, the data link is located under the left hand side of the instrument panel. On all models, turn the ignition switch to the On position. At this point, the "Check Engine" light should flash. codes


25011203-uqsqk1sqel1nykdqv4diatnw-3-0.jpg 12pin version below.
jump pins,(for PCM errors) pins A > B
25011203-uqsqk1sqel1nykdqv4diatnw-3-1.gif
the codes are here.
http://www.troublecodes.net/isuzu/iszucel/





25011203-uqsqk1sqel1nykdqv4diatnw-3-3.jpg see no in the engine bay at all, like the 1 guess

Aug 26, 2014 | 1993 Isuzu Amigo

1 Answer

Engine diagram isuzu


immediately costs money. sorry, but that is a fact.
i'm slow but
alldata.com has this.
for $15 , log in and look and not wonder.

the FSM is sold used, buy one.
but the FSM shows like 100 pages of diagrams on the engine.
for all related systems.
we cant post those 100 pages.
why not,just post symtoms or if doing service state the object or action desired, so we can match need to drawings.

I do the under dog cars, , the ones nobody buys.
Isuzu, Suzuki, and Yugo.
tell what you are doing.

old post.

Apr 05, 2014 | 1995 Isuzu Pickup

1 Answer

Sputters and dies on cold start, significant drop in gas mileage.


You need to rebuild the carburetor or clean the choke linkage and make sure the choke valve closes cold.

Nov 12, 2013 | 1985 Isuzu Pickup

1 Answer

I need the Key Code for a 1994 Isuzu Pick up truck Ignition & doors


its in the owners manuall and sometimes behind the glove box. Lift rear hatch and look in the door jam sometimes its on a sticker there.

Feb 27, 2012 | 1994 Isuzu Pickup

1 Answer

Where is the fuel filter located in a 1991 Isuzu pickup? Appreciate any assistance.


Open the hood. Move to the front of the engine and locatethe fuel filter. The filter mounts to the inside of the passenger-side framerail.

Feb 01, 2011 | 1991 Isuzu Pickup

1 Answer

What all do i need to rebuild my isuzu motor that is a 1.8 liter 4 cylnder


Well, you'll need a gasket set, and whatever parts you're going to replace, like bearings for the crankshaft and rings for the pistons, etc.

Also, you might need a timing belt if yours has one.

I once rebuilt a 1979 Honda Accord 1.8L engine this way.

The dealer can help you find the right parts for your engine.

Purchase a book on the subject, as the rebuild process can be complicated.

Also, you need a garage to keep your parts clean and dry as you perform the rebuild process.

Helps to have electricity in the garage for lighting up your work space.

Need a torque wrench to tighten down the head bolts, and socket wrench set for undoing bolts in the first place.

That's basically all I remember from doing the job on the 1979 Honda
Accord in the 80s which probably would apply to your Isuzu motor.

Jul 04, 2010 | 1990 Isuzu Pickup

Not finding what you are looking for?
1993 Isuzu Pickup Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...