Question about 1998 Toyota Tacoma

Open Question

1998 Toyota Tacoma Will not start after battery being disconnected. Do you have to reset security system with remote before it will start?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: auto theft alarm went off,

get in truck shut door . . . turn key to acc position. . .push alarm button on dash near ECT button. turn key back off .. . then to the acc position again. . then push button back like it originally was. this should help i had the same problem . only i was in the middle of the woods with no cell phone signal!

Posted on Mar 10, 2009

  • 15 Answers

SOURCE: 1996 Toyota Celica remote security system no longer works

Hi, Contact your dealer and get instructions for reprogramming your remotes. When a security system loses power for an extended amount of time the programming for the remotes are lost.

Posted on Mar 09, 2009

  • 2 Answers

SOURCE: After disconnecting the battery and then

If after unlocking the driver door with the key and still no luck, put the key in the ignition and turn forward to start (if it won't start turn forward anyway) then push you're red reset button on the dash. That should do it.

Posted on Sep 12, 2009

arauzvictor1
  • 466 Answers

SOURCE: how do i remove the manuel clutch to a 1998 tacoma

If you want to change the "Remove clucht trasmision bars front and rear, remove the cylinder in the booth attendant said you have to remove the gear-change broadcasts have jack-remove the bracket that supports the transmission back-to remove the exhaust pipe - Put the jack, remove the screws that attach the transmission with the engine off, remove the transmission clucht well ... You have to ensure the transmission on the jack will not fall

Posted on Jan 11, 2010

  • 1861 Answers

SOURCE: 1998 toyota tacoma efi fuse blows when trying to

Hello. Welcome to FixYa.

I have observed this condition many, many times.

The most common cause of this problem is a short-to-ground at the fuel tank wiring harness. If you can get to the wiring connction on top of the tank, and disconnect it, replace the fuse, and, with the wiring harness still disconnected, try to start it again. If the EFI fuse does not blow, the fuel tank sending unit assembly is the culprit, and it will need to be replaced. Rust and corrosion cause the power wire to short out. This is a very common problem.

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck battery went dead put new battery on now can't set colors or the clock1998


You will need to have the dealer reset the system for you. Next time use a battery backup when the main battery is disconnected.

Aug 10, 2016 | 1998 Toyota Tacoma

1 Answer

Changed battery in 98 tacoma and when hooking cables back up...horn keeps going off. How do I stop it?


factory alarm will sound when you reconnect battery, have remote handy and press the unlock button when you make the connection

Sep 16, 2011 | 1998 Toyota Tacoma

1 Answer

How to remove the starter from a 2007 toyota tacoma?


Hi,

1.Raise the hood of your Tacoma. Disconnect the negative battery cable with a wrench and isolate the cable away from the battery
2.
Raise the hood of your Tacoma. Disconnect the negative battery cable with a wrench and isolate the cable away from the battery

3.
Remove the nut securing the battery cable to the starter body with a wrench. Pull the battery cable off the post away from the starter. Pull the other wiring connection straight out of the connector.

4.
Remove the mounting bolts securing the starter body to the bell housing with a socket and ratchet. Support the starter body while you remove the mounting bolts, then pull the starter out of the bell housing.



Good luck!!!

Aug 06, 2010 | 2007 Toyota Tacoma

1 Answer

1998 toyota tacoma efi fuse blows when trying to start


Hello. Welcome to FixYa.

I have observed this condition many, many times.

The most common cause of this problem is a short-to-ground at the fuel tank wiring harness. If you can get to the wiring connction on top of the tank, and disconnect it, replace the fuse, and, with the wiring harness still disconnected, try to start it again. If the EFI fuse does not blow, the fuel tank sending unit assembly is the culprit, and it will need to be replaced. Rust and corrosion cause the power wire to short out. This is a very common problem.

Feb 27, 2010 | 1998 Toyota Tacoma

2 Answers

After disconnecting the battery and then reconnecting it on my 2000 Toyota Tacoma, the alarm goes off and the car will not start. I do not have a remote for this car and need help in a course of action. I...


If after unlocking the driver door with the key and still no luck, put the key in the ignition and turn forward to start (if it won't start turn forward anyway) then push you're red reset button on the dash. That should do it.

Jul 10, 2009 | 2001 Toyota Tundra

1 Answer

Code po441 check engine. incorrect purge. how do i fix? 2oo2 toyota tacoma 4x4 at.


first try to reset the ecu, disconnect the negative battery terminal few minutes, then reconnect start engine and test

Jun 17, 2009 | 2002 Toyota Tacoma

2 Answers

Starting problem


This may sound like a problem with a fuel pump. To test if it is with the security system, with a battery in parallel or a working battery, you should be able to disable the alarm via the key or have it manually disabled, then see if it will start

Jun 03, 2009 | 1996 Toyota Tacoma

1 Answer

Cannot start engine after alarm sounded.


disconect the battery for about 15 minutes and turn the head lights on after bat is disconected and then turn head lights off reconect bat and this should reset your alarm system.

Apr 21, 2009 | 2002 Toyota Tacoma

2 Answers

1996 Toyota Celica remote security system no longer works


Hi, Contact your dealer and get instructions for reprogramming your remotes. When a security system loses power for an extended amount of time the programming for the remotes are lost.

Mar 09, 2009 | 1996 Toyota Celica

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...