Question about 2008 Ford Territory 4.0

Open Question

Replacing ford territory front wheel bearings

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

Hentie
  • 18 Answers

SOURCE: after replacing the left front wheel bearing on a 2003 ford focus, the abs and traction warning light stay on

The bearings on the wheels has to be installed one way only, the rotor ring is built into the bearing and if installed the wrong way round the sensor cant pick up the wheel speed causing the ligt to be switched on in the cluster. The diagnostic equipment should pick this up as a fault once the car has been driven, it will see the sensor when you do the diagnostic if the car is standing still but once the car is moving and no signal is send from that wheel it would register a fault into the memory of the PCM that you would be able to retrieve later.
There is a way for you to test the sensor yourself by using a multimeter set on volts, you jack the vehicle up at that wheel, install a vehicle stand to support the vehicle to be safe, disconect the wheel speed sensor and probe the two wires into the sensor, spin the wheel by hand and a small amount of current will be produced meaning the the sensor is working and the wheel bearing is installed the correct way, you can also do a continuaty test on the sensor by switching the multimeter onto ohms, but be very carefull, if this sensor has three wires you cant do the continuaty test because of the integrated circuit in the sensor, the three wire sensors opperate on a voltage from 5Volt and it would be destroyed by the multimeter opperating on 9Volt.
If the continuaty test passes and the bearing is installed the correct way, the most comon fault would be a break in the wiring leading to the PCM
Hope this will be helpfull.

Posted on May 04, 2009

  • 27 Answers

SOURCE: replace rear wheel bearing 2002 ford explorer 4x4

you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Posted on Aug 15, 2009

  • 23 Answers

SOURCE: replace front wheel bearings 99 ford explorer

not press fitted, standard tapered bearings, if 4X4 it is a little more involved, just dont misplace any of the smaller parts and you will be fine.

Posted on Aug 29, 2009

Testimonial: "thanks for the speedy reply and also for the right advice."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there any reason why I couldn't replace my front wheel bearings on my 09 territory awd myself.....??


getting thehub off you can do but you will need a decent workshop press to get the old bearing off and to press the new ones on
if you get the hub off and take it to an accredited shop along with the new bearing they can press it off and on for you

May 13, 2017 | Cars & Trucks

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

I have movement in my wheel when it's jacked up , but when on ground none


there is to be no free play( movement ) in the wheel bearings
the optimum position is no free play no pre load in the bearings you may need a workshop manual to get it right as the bearing play may not be adjustable
If it is a one piece bearing running two thrust ball bearings , the end play will be preset
it is only adjustable if tapered roller bearings are used

Apr 01, 2016 | 2006 Ford Territory 4.0

1 Answer

Ford territory rotor removal


front or rear wheel to different proceedure's

Feb 19, 2015 | 2006 Ford Territory 4.0

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

2 Answers

Fixing a 2003 ford focus front wheel bearings


remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee

Sep 07, 2009 | 2003 Ford Focus

1 Answer

Replace front wheel bearings 99 ford explorer


not press fitted, standard tapered bearings, if 4X4 it is a little more involved, just dont misplace any of the smaller parts and you will be fine.

Aug 29, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
2008 Ford Territory 4.0 Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...