Question about Jeep Grand Cherokee

Open Question

2002 jeep grand cherokee laredo engine code p1762 this is the number that come up when i check the coumputer

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2002 jeep cherokee laredo

the only problem that vehicle has is with cooling fans is relay/module or electrical harness to module that burns up located behind and under right front headlamp assy must remove headlamp to access relay/module that is what powers up fan motor module assy.

Posted on Aug 10, 2008

  • 114 Answers

SOURCE: 2002 wj jeep grand cherokee p1756

The governor pressure sensor is the most likley cause however an inspection of fluid or debris in trans pan would be a good idea to make sure there's nothing excessive in it. Attached is a list of possible causes however the senor would be the most common.

POSSIBLE CAUSES

  • Powertrain control module
  • 5 volt supply circuit open
  • Check transmission fluid level and condition
  • GOV press sensor signal circuit shorted to voltage
  • GOV press sensor signal circuit shorted to sensor ground
  • GOV press sensor signal circuit shorted to ground
  • GOV pressure sensor signal circuit open
  • Sensor ground circuit open
  • GOV press sensor signal circuit shorted to voltage inside transmission
  • 5 volt supply circuit open inside transmission
  • Intermittent governor pressure solenoid
  • Internal transmission problem
  • Oil burnt or oil pan has excessive debris
  • Other transmission DTC'S
  • GOV press sensor signal circuit shorted to sensor ground inside transmission
  • Valve body
  • GOV press sensor signal circuit shorted to ground inside transmission
  • GOV press sensor signal circuit open inside transmission
  • GOV press sensor ground circuit open inside transmission
  • Governor pressure sensor (high)

Posted on Mar 26, 2009

  • 52 Answers

SOURCE: 96 Jeep Grand Cherokee diagnostic codes P1762 and

governor pressure sensor in transmission is the likely problem

Posted on Nov 22, 2009

c17hydro
  • 2984 Answers

SOURCE: 1998 Jeep Grand Cherokee Laredo 4.oL I got a code po113

Trouble Code: P0113 (4.0L L6 VIN S Auto)
IAT Sensor Circuit High Input Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details

Trouble Code Conditions:
Check with ignition on or engine running; battery voltage more than 10v; The PCM detected the IAT Sensor input was over 4.90v (exc. Dakota, Durango, Ram) or 4.98v (Dakota, Durango, Ram) for 3 seconds.

Possible Causes:
  • IAT Sensor signal circuit shorted to VREF (5v)
  • IAT Sensor signal circuit is open, or the ground circuit is open
  • IAT Sensor is damaged or it has failed (an internal open circuit)
  • PCM has failed


d1eaead.gif

Posted on Dec 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Grand Cherokee laredo with p1762 trouble code. Found that transmission fuild was down over 2 qts. Added fuild, then reset the code. Code went away. Should I still have mechanic check this?


hi
you have sorted the problem, the fault code that you had is caused by low transmission fluid. BUT.....
you still have to check the transmission for leak, to find out why the fluid went down that much
Good luck

Feb 16, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Purge valve engine code


check the number 10 fuse should be a 15a but it says open in th emanual but it was not on mine see link
http://dorisong.com/poolsideinsouthcove/1999-jeep-grand-cherokee-laredo-fuse-diagram-20.jpg

Mar 26, 2012 | 1999 Jeep Grand Cherokee

1 Answer

Hi We own the 2002 jeep grande cherokee laredo


Maybe ask the delership and they will tell ya or check the manual for number of seating.

Sep 19, 2011 | 2002 Jeep Grand Cherokee

2 Answers

Shifting Problems on Jeep Grand Cherokee


Your Kick down cable is either on too short or come off completely. Check that first before you spend any money on anything else or transmission overhaul

Aug 09, 2009 | 2001 Jeep Grand Cherokee

1 Answer

2002 jeep grand cherokee laredo engine light on and car skips a bit now and then. Could this be something with the transmission?


check to see what the codes are in the computer. if it is a 300 to 306 or 308 depending on the engine size.these are mifire codes whitch would cause one to cut out off and on and turn on the light.
then you can see if it is plugs,wires,injectors, ect....

Jun 16, 2009 | 2002 Jeep Grand Cherokee

2 Answers

Diagnostics "P1762 Manufac. Contrl. Transmission"


Had the same code on my 2002 Jeep Grand Cherokee. Started having shifting problems as well. Code is for governor pressure sensor on trans. Cost me about $800 for dealer to fix. No problems after part changed out.

May 22, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Code p1762 is appearing on my jeep dashborad


Governor Pressure Sensor Offset Volts Too Low or High

Mar 22, 2009 | 2004 Jeep Grand Cherokee

1 Answer

1993 JEEP GRAND CHEROKEE LAREDO- TRUCK WONT


OK...I have a 93 outside...one diagram I have shows an ignition module next to coil...but there is none on mine, (4.0 engine)
Two items to check are crank sensor and cam sensor inside distributor. Test procedure can be found in just about any manual including haynes.
You will need a decent volt/ohm meter to do testing. You can also check codes by turning ignition switch on/off three times, leaving it on the third time. Check engine will flash code #'s (ex: one flash, pause two flashes= the number twelve.then followed by a longer pause then another set of flashes etc.)

Mar 05, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Grand Cherokee laredo P1763 and P1762


It's a transmission related problem, that you should have looked at a.s.a.p. to avoid costly transmission repairs down the road. Have it scanned at a reputable transmission repair place, dealer, or mechanic you trust. The drain pan will have to come off to perform repair, so have a transmission service (filter & fluid) done while your at it, unless it was done recently.

Jan 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Check engien lihgt with code p1762


CEL Code P1762 is Governor Pressure Sensor Offset Improper Voltage. Make sure all your wires going to the sensor are ok, then if they are I would look into a new Sensor. Hope this gives you some direction. Thanks for Using FixYa!

Sincerely,

JC

Nov 29, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...