Question about Cars & Trucks

Open Question

How to remove rear motor mount 02 cougar - Cars & Trucks

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: how many motor mounts does a neon 02 have

You have 4 mounts:

2 rear mounts...look like this:

87745f3.jpg
Front right Upper:

aa662e8.jpg
Front Right Lower:

d8e78b6.jpg

Posted on Nov 01, 2009

  • 538 Answers

SOURCE: I removed my old motor

You may have to take the other mounts loose and then carefully jack the engine up enough to get the new mount in. Put a block of wood between the jack and the bottom of the engine so as not to damage or dent the oil pan.

Posted on Dec 09, 2009

  • 10 Answers

SOURCE: REMOVE REAR MOTOR MOUNT ON 1995 MAZDA PROTEGE

to remove that support is recommended to use keys of extensions to be used by the top and back of the engine,,,recommended to release the air filter and battery sleeve for space

Posted on Apr 11, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The motor stalls when the heating direction knob is turned on


2002 Mercury Cougar V6 2.5L problem - YouTube

? 2:28
https://www.youtube.com/watch?v=zUu256ADwJA
Jun 2, 2012 - Uploaded by 1chrisrg
U know how to adjust idle speed manually on 2000 mercury cougar? ... You may drive and the hole is too small and the coug will stall. .... I replaced the IAC and now if sounds like my engineis in a race ... I just bought a 99 Cougar. ... new edge cougar owners forums and I believe there are directions on ...

How to replace heater control panel switch knobs remove ...

? 5:01
https://www.youtube.com/watch?v=abBINs_zWh8
Jul 12, 2013 - Uploaded by kirk colombo
02 explorer - remove dash panel and replace heater and air conditioning control switch knobs. Can also ...Missing: cougar ‎stalls

A/C & Heater Controls for Mercury ' eBay




Dec 13, 2015 | 1999 Mercury Cougar

1 Answer

How to replace left control arm on 99 mercury cougar


Here's what I found on Yahoo answers:
For the driver's side: yes, you will have to raise the motor.
On all models, remove the front motor mount, Mark the position of the right engine mount, remove 3 right engine to mount bolts. remove one right engine mount to body nut. On all models hold the strut shaft with an 8 mm allen wrench, loosen top retaining nut 5 turns. Raise vehicle, remove ball joint to steering knuckle pinch bolt. seperate control arm ball joints from steering knuckle. Do NOT damage ball joint seal. Remove pinch bolt attaching steering knuckle to strut. Slide steering knuckle up on strut, Move transaxle to gain access to control arm nuts and bolts. remove 2 nuts and bolts and attaching control arm to subframe. Lifting up control arm remove.
Now this to mark the motor mount because you are supposed to use a powertrain alignment guage when putting back together. if not you can bind the motor in the unibody and make for a shaky ride.
that drivers side lower control arm calls for 4.3 hours where as the passenger side calls for 1.3 hours. So you can see what your in for.
BTW these instructions are taken straight from the Ford repair manual.

Source(s):

http://mysite.verizon.net/t2bedlam/fr.jp...

Jan 02, 2013 | 1999 Mercury Cougar

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

2 Answers

Blower motor removal in a 1999 mercury cougar


SECTION 412-02: Heating and Ventilation 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001 Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
    m3401035.jpg
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.
    m3401077.jpg
Installation
  1. NOTE: Engage the securing tab for the blower motor.

Nov 12, 2010 | 1999 Mercury Cougar

1 Answer

I am trying to remove the starting motor from my 1999 mercury cougar 2.5 V6. need some help as to how to go about this


2.5L Engine
See Figure 5


0900c152800a88de.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Starter mounting-2.5L engine

  1. Disconnect the negative battery cable.
  2. Remove the engine air cleaner assembly.
  3. Remove the fuel feed and return lines from the support bracket located on the accelerator cable bracket, and remove the fuel line bracket.
  4. On vehicles equipped with a automatic transaxle, remove the gear selector and the gear shift cable bracket from the transaxle.
  5. Remove the air cleaner support bracket from the engine and transaxle mount.
  6. Remove the nuts on the starter terminals and remove the cables from the terminals.
  7. Remove the starter motor-to-transaxle case retaining bolt at the rear of the starter.
  8. Remove the two starter retaining bolts and carefully lift the starter from the transaxle case while disengaging the alignment pins.

To install:
  1. Position the starter onto the alignment pins and onto the transaxle case.
  2. Install the two starter retaining bolts and the rear retaining bolt and tighten them to 15-21 ft. lbs. (21-29 Nm).
  3. Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm).
  4. Install the air cleaner support bracket.
  5. If removed, install the gear shift selector and bracket.
  6. Install the fuel line bracket and install the fuel lines in the bracket.
  7. Install the air cleaner assembly.
  8. Connect the negative battery cable.


Full tutorial at autozone.com, just log in and search starter

Nov 01, 2010 | 1999 Mercury Cougar

1 Answer

How many motor mounts does a neon 02 have


You have 4 mounts:

2 rear mounts...look like this:

87745f3.jpg
Front right Upper:

aa662e8.jpg
Front Right Lower:

d8e78b6.jpg

Nov 01, 2009 | 2002 Dodge Neon

1 Answer

My 2001 Mercury Cougar moonroof is stuck, it opened a few inches then just stopped. Is there a way I can manually close it?


Check fuses #21 40 amp check relay jump 12 volts to motor circuit
Overhead Console Removal
  1. Disconnect the battery ground cable.
  1. NOTE: Remove the interior lamp as a unit.
    Ease out the interior lamp.
    • Disconnect the electrical connectors.
    v4301245.jpg
  1. Remove the overhead console screws.
    v4301246.jpg
  1. Remove the overhead console.
    • Apply an even downwards force to both sides of the console.
    • Disconnect the roof opening panel switch electrical connector (if equipped).
    • Disconnect the information and message center electrical connector (if equipped)
-----------------------------------------------------
SECTION 501-17: Roof Opening Panel 2001 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001
Roof Opening Panel Motor Removal
  1. Remove the overhead console. For additional information, refer to Section 501-12.
  1. Disconnect the sliding roof motor electrical connector.
    v4101317.jpg
  1. Disconnect the sliding roof panel relay.
    v4101318.jpg
  1. Remove the sliding roof motor control unit.
    v4101322.jpg
Installation
  1. To install, reverse the removal procedure.

Oct 30, 2009 | 2001 Mercury Cougar

1 Answer

Engine monts


Normally you put a floor jack under the engine front or flywheel with a 2x6 cushion board attached and jack it up an inch or so to releave the pressure on the motor mount. Then with mechanic tools and wrenchs remove and replace the motor mount.

May 10, 2009 | 1988 Mercury Cougar

1 Answer

How can i replace it?


http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal
  1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
  2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
  3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
  4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
  5. Support the transaxle with a floor jack.
  6. Remove the front transaxle support insulator through bolt and nut.
  7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal
  1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
  1. Raise and support the vehicle.
  1. Remove the three rear transaxle support insulator nuts.




  1. Lower the vehicle.
  1. Remove the rear transaxle support insulator from the vehicle.

Mar 29, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...