Question about Ford Econoline Cargo

1 Answer

Procedure to r&r oil pump - Econoline Cargo Ford Cars & Trucks

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    procedure to do what with oil pump

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

To remove the oil pump you will need to drop the oil pan to gain access to the oil pump. Difficulty depends on what engine is in the van and clearances available to remove the pan. But, basically an easy process if you have any mechanical skills and the correct tools for the process.
Be sure to prime the new oil pump before you install it or start the engine.

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put new bearings in the bottom end of a 05 grand caravan. 3.8. how do i prime the oil pump now?


If the oil pump is still accessible, I'd pour some oil into the outlet, then install it. Also, pour as much oil into the oil filter as it will take without spilling when you install the filter (I always do this when I change an oil filter; it reduces wear on the engine during the first startup following the change). Put in the remaining amount of oil required in the usual fashion; the oil level in the pan should be high enough to prime the pump.

Note: this is a generic procedure. To be absolutely certain, check the Chrysler service, Chilton's or Haines' manual for your vehicle to see if a different procedure is required for oil pump installation.

Jan 27, 2015 | Cars & Trucks

2 Answers

Ran out of engine oil and after i refilled, it wont start


I the engine ran completely out of oil, the engine has been cooked and is probably locked up from the friction between unlubricated metal moving parts. Also may have spun bearings which means the main or rod bearings stacked on top of each other causing the engine to lockup. If you ran the engine without oil until it quit you will probably need a new engine.

Dec 06, 2013 | 2006 Volvo S40

1 Answer

Procedure for removing oil pump 2001 GMC serra


The oil pump and screen should be in the bottom of the oil pan. Which would need to be removed to get access to it.

Sep 30, 2012 | GMC Cars & Trucks

1 Answer

Oil pump replacement


To replace oil pump, you first need to drain the remaining oil, then drain the cooling system.The oil pump is held by bolts.The bolts needs to be removed.The belt and crank shaft pulley also needs to be removed. Its not very easy to replace.But if you have proper procedure with details and diagrams, then yes you can do it. For complete procedure with details,click this link below:--- http://technoanswers.blogspot.com/2011/10/how-to-replace-oil-pump-on-chevrolet.html --------- This should help.Thanks.Helpmech.

Oct 19, 2011 | 2002 Chevrolet Tracker

1 Answer

I know it's the oil pump that needs replaced i just don't know exactly where it is.. how hard is it going to be for me to get to? What do i have to take off to get to it? Or what is the procedure...


its in the oil pan. jacking up vehicle removing oil pan , new gasket. get torx specs for oil pump bolts an oil pan bolts
ps buy a new oil pump. NEVER rebuilt one.

Jun 03, 2011 | Oldsmobile Achieva Cars & Trucks

1 Answer

Need to replace oil pump


Oil Pump Replacement REMOVAL
  1. Remove the oil pan.
  2. Remove the oil pump from rear main bearing cap.
INSTALLATION
  1. Install oil pump. During installation slowly rotate pump body to ensure driveshaft-to-pump rotor shaft engagement.
  2. Hold the oil pump base flush against mating surface on No.5 main bearing cap. Finger tighten pump attaching bolts. Tighten attaching bolts to 41 Nm (30 ft. lbs.) torque.
  3. Install the oil pan
  4. This procedure is for the 3.9L, 5.2L and 5.9L

Feb 21, 2011 | 1999 Dodge Durango

1 Answer

How long and easy is it to rebuild oil pump on 94 grand caravan 3.8l


Don't bother. Replace the unit.
3.0 liter
The oil pump assembly used on this engine is mounted at the front of the crankshaft. The oil pump also retains the crankshaft front oil seal.
  1. Remove the accessory drive belts.
  2. Remove the timing belt cover and timing belt. Refer to the timing belt removal and installation procedures in this section.
  3. Remove the crankshaft sprocket.
  4. Remove the oil pump mounting bolts (5), and remove oil pump assembly. Mark mounting bolts for proper installation during reassembly.

To install:
  1. Clean the oil pump and engine block gasket surfaces thoroughly.
  2. Position a new gasket on pump assembly and install on cylinder block. Make sure correct length bolts are in proper locations and tighten all bolts to 10 ft. lbs. (14 Nm).
  3. Install the crankshaft sprocket and timing belt. Recheck engine timing marks.
  4. Install the timing belt covers. For more details, refer to the timing belt cover installation procedures.
  5. Install the accessory drive belts.
  6. Refill the crankcase and start the engine.
  7. Check for correct engine oil pressure and for any oil leakage.
3.3 and 3.8 liter engines


  1. Disconnect the negative battery cable. Remove the dipstick.
  2. Raise the vehicle and support safely. Drain the oil and remove the oil pan.
  3. Remove the oil pickup.
  4. Remove the chain case cover.
  5. Disassemble the oil pump as required.

To install:
  1. Assemble the pump. Tighten the cover screws to 10 ft. lbs. (14 Nm).
  2. Prime the oil pump by filling the rotor cavity with fresh oil and turning the rotors until oil comes out the pressure port. Repeat a few times until no air bubbles are present.
  3. Install the chain case cover.
  4. Clean out the oil pickup or replace as required. Replace the oil pickup O-ring and install the pickup to the pump.
  5. Install the oil pan.
  6. Install the dipstick. Fill the engine with the proper amount of oil.
  7. Connect the negative battery cable and check the oil pressure. Check for any oil leaks.
for the 3.3 you can rebuild, 3.0 - replace.

Feb 15, 2011 | 1994 Dodge Caravan

2 Answers

How to replace oil pump


REMOVAL & INSTALLATION

Gasoline Engines
See Figures 1 and 2


7ec529c.jpg
Fig. Fig. 1: Exploded view of the oil pump used on 2.0L and 2.3L gasoline engines


20995b0.jpg
Fig. Fig. 2: Exploded view of the oil pump used on the 4.0L engine-2.8L and 2.9L engines are similar
  1. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly.
  2. Remove the oil pump retainer bolts and remove the oil pump.

To install:
  1. Prime the oil pump with clean engine oil by filling either the inlet or outlet port with clean engine oil.
  2. Rotate the pump shaft to distribute the oil within the pump body. Install the pump and tighten the mounting bolts to 14-21 ft. lbs. on 2.0L and 2.3L engines; 6-10 ft. lbs. on 2.8L and 2.9L engines or 13-15 ft. lbs. on 4.0L engines.

Do not force the oil pump if it does not seat readily. The oil pump driveshaft may be misaligned with the distributor shaft assembly. To align, rotate the intermediate driveshaft into a new position.
  1. Install the oil pan as previously described. The oil pumps are not serviceable. If defective, they must be replaced.

Remember rated this.

Aug 11, 2010 | 1989 Ford Ranger

1 Answer

How do I remove oil pump on 2000 Plymouth voyger


The oil pump removal procedure for Plymouth Voyager 2000.
A oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.
The procedure to remove oil pump is as follows:--
  • Drive your vehicle up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.
  • Remove the engine front cover then drain the engine oil and take out the oil pan. It is under the engine and looks like the bottom of the motor.
  • Unscrew the oil pump mounting bolts with a wrench and proceed to remove the oil pump itself by pulling it down and out of the engine. Avoid getting any contaminants into the oil pump assembly while removing.
The Water pump removal procedure for Plymouth Voyager 2000.
The water pump is the heart of the Plymouth Voyager's cooling system, circulating the coolant. When the water pump is faulty, it can cause serious damage to the engine of your Plymouth Voyager.
  • Disconnect the negative battery cable.Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
  • Remove the right inner splash shield and the accessory drive belts. Support the engine underneath and remove the right motor mount with the bracket.
  • Take off the front cover and remove the timing belt along with the timing belt idler pulley. Also remove the camshaft sprockets, the rear cover to the timing belt and the alternator with its bracket.
  • Loosen and remove the bolts to the water pump and remove it from the engine.Install the new water pump after inserting a new o-ring gasket. Tighten the bolts to 105-inch lbs. Make sure that the pump can move freely by rotating it by hand.
  • Replace all components in reverse order. Tighten the camshaft sprocket bolts to 75 foot pounds and the timing belt idler pulley to 45 foot pounds.
  • Refill the cooling system with coolant and reconnect the negative battery cable. Start the engine and check for leaks when it reaches normal operating temperatures.

Loud noises coming from the cooling system could be a sign that your water pump needs replacing. A leak in the coolant may also be an indicator. You can expect that a water pump will need to be changed every 70 to 100 thousand miles or so in a Plymouth Voyager vehicle.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jun 13, 2010 | 2000 Plymouth Voyager

2 Answers

OIL PUMP


This Depends on a 2 Details, ENGINE Size 4by4 or NOT. Most are Fairly Simple Once the Oil Pan has been Removed and the OIL PAN is Normaly the HARDEST Part of it

AFTER OIL PAN REMOVAL
  1. Remove the oil pump. Refer to Oil Pump, Pump Screen and Deflector Removal.
  2. A loose screen or pipe assembly can result in an air leak and loss of oil pressure. For more information, refer to Oil Pump Clean and Inspect.
INSTALLATION PROCEDURE
.
  1. Install the oil pump and the oil deflector. Do not reuse the oil pump drive shaft retainer (4). During assembly, install a NEW oil pump driveshaft retainer. Refer to Oil Pump, Pump Screen and Deflector Installation.
  2. Install the engine oil pan. Refer to Oil Pan Replacement

Dec 09, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...