Question about 2008 Peugeot 207 SW

Open Question

Heated rear screen not working on peugeot 207

How do I remove tailgate trim to get to the wiring connections so that I can try and locate the problem. 40amp fuse is OK. Heated mirrors are OK. Rear wiper OK.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: Peugeot 406 SV rear seat removal

take it you have done it------- two brackets at front of seat

Posted on Nov 20, 2008

  • 274 Answers

SOURCE: how can i remove the rear axle hub nut lockplate

remove tin cover from center of hub
use 30mm socket on a strong arm to remove nut
if re using old nuts only do so if they have only been staked over once and that you have swapped them from left fo right

Posted on Dec 09, 2009

Testimonial: "your answer have been very helpful.i try. thanks very much"

czaa
  • 4514 Answers

SOURCE: peugeot 406 hdi turns over but wont start, no

chec the fuse box for bad then do an inspection of the wires for any corrosion/cuts--may hav a module thats bad or computer problem-get a tech that can do a mobile scan

Posted on Dec 31, 2009

Raysagem
  • 1017 Answers

SOURCE: Peugeot 407 SW 2006 wash wipe, no water coming from front.

The pipe that caries the water come off the connector under the wheel arch, you have to take the wheel off on the side of the water reservoir and the protective lining. Apply a bit of super glue to it, it's not very difficult to do.

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: how do i remove rear inner door panel on my Peugeot 407

should be screws behind rear door handle u have to take cover of screws will be behind u also need to remove the winder 4 window if manual and not electric the panel itself will be held on with poppers just grab bottom of panel and pull hard then work yuor way up sides once you have unclicked poppers from bottom and side of panel grab panel and push upwards as most weather strips are attached to the panel .

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i clear my rear jet


Assuming you mean rear washer jet:

The whole high-level brake light unit (which the rear washer jet is part of) can be pushed out by raising the rear door and locating and pushing on the two locating studs behind the unit. The uniot should then move forward and after detacing the wiring connector and fluid hose, can be removed.

Poke something like a tooth pick into the jet inlet and/or try blowing through the jet until the obstruction has gone.

Mar 30, 2013 | 2008 Peugeot 207 Sport

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

2 Answers

The tailgate wont open on my 02 peugeot 307


It is controlled through an electronic relay mounted in tailgate handle. If it has some rust then it doesn't close the circuit to release the lock. just clean the relay switch and it'll work (but to unmount this handle you'll need to open the gate first and then you'll access the switch by removing the plastic trim from inside the tailgate or better let it done by a mechanic or car electrician).

Apr 09, 2010 | 2006 Peugeot 405

1 Answer

How to remove rear door panels on a 2003 ford f 250to get to door switch


Tailgate latch, handle and lock
  • Open the tailgate.
  • Remove the two bolts and detach the door stop.
  • Lower the tailgate and remove the tailgate access cover.
  • Disconnect the control rods.
  • Detach the retaining nuts and remove the handle and lock cylinder assembly from the tailgate.
...
Door trim panels
  • Disconnect the cable(s) from the negative battery terminal(s).
  • On manual window equipped models, pull the window crank cover aside, remove the screw and detach the handle.
  • On the front door of power window equipped models Pry up on the retaining clip at the front edge of the armrest and lift the armrest switch control plate out and disconnect the electrical connections,then remove the retaining bolt from the opening.
  • Use a small screwdriver to pry off the courtesy light cover for access to the trim panel retaining bolt.
  • Carefully pry off the mirror trim panel from above the front edge of the door panel.
  • Once all of the bolts are removed, remove the trim panel by gently pullingit up and out .Detach the courtesy light bulb housing from the panel.
  • For access to the inner door components, remove the speaker (if it would interfere with watershield removal) and the screws from the trim piece at the lower trailing corner of the door, then carefully peel the watershield from the door.
  • Remove the screws securing the latch.
  • Working through the large access hole, position the latch as necessary to disconnect the electrical connector and disengage the outside door handle and outside lock cylinder to latch rods and the inside handle-to-Iatch cable.
  • Detach the locking rods by unsnapping The remaining outside handle retaining nut can be reached through the access hole in the door frame and the upper striker the portionof the plastic clip engaging the connecting rod, then pulling the rod out of its locating hole.
  • Position the latch as necessary to disengage the door lock actuator hook. Detach the cable cover and disconnect the cable from the latch. Remove the latch assembly from the door.

Oct 30, 2009 | 2003 Ford F250 Super Duty Crew Cab

2 Answers

Break pads on a 207


hallo
remove two bolts from behind
Marko

Sep 30, 2009 | Peugeot Cars & Trucks

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

1 Answer

My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling


Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Jul 24, 2009 | 2001 Chrysler Town & Country

1 Answer

Remove lower rear trim beneath tailgate


Easy. First you need to remove the rear splash guards(the plastic pieces located near the tires)
After that, it should be about 6 bolts/clips and they are located in plain view just standing facing the bumper. Then the bumper pulls right out.

Good luck

Apr 20, 2009 | 2009 Honda CR-V

2 Answers

1987 toyota 4runner tailgate window stopped working


REMOVE THE REAR TRIM PANEL ON THE TAILGATE AND SEE IF THE MOTOR IS GETTING 12 VOLTS AND A GOOD CHASSIS GROUND CONNECTION, MANY TIMES THE WIRING HARNESS THAT GOES IN TO THE TAILGATE DEVELOPES A OPEN/BROKEN WIRE FROM THE REPEATED OPENING AND CLOSING OF THE TAILGATE, THE WIRE BREAKS INSIDE THE PLASTIC INSULATOR AROUND THE WIRE, SO IT IS NOT APPARENT ON VISUAL INSPECTION, REQUIRES THE USE OF AN OHM METER AND A VOLT METER.

Mar 30, 2009 | 1987 Toyota 4Runner

Not finding what you are looking for?
2008 Peugeot 207 SW Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...