Question about 2007 Toyota Corolla

1 Answer

To clarify my post, driver side rear brake light does not work when braking. Need help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Easy, jus replace the bulb. No more than $20 and it should b an easy on n off wit little to no tools. But first have someone look at the lights or u and with the key in the on position engine off and lights on, does everything light up? If yes good. Then have have the person or yourself step on the brakes and if the passenger side brake light do light up and obviously not ur driver side then its and easy bulb replacement.

Posted on Jan 23, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 166 Answers

SOURCE: 2002 Camry Brake lights

sounds like you nee a couple of new globes

Posted on Dec 20, 2008

  • 4 Answers

SOURCE: THE BRAKE LIGHT WARNING LIGHT COMES ON AND THE

well here's a start towards ur problem, due to the auto circuits u have an open return to the negative side of the battery. Have you done anything with the vehicle's systems before this started? the reason fo the strange lighting is that a positive voltage is being applied to what normally would be return side. You will need to get an electrical diagram if possible to pin point area if as previously asked didn't occur.

Posted on Mar 02, 2009

  • 150 Answers

SOURCE: 2005 Toyota Sienna rear brake light problem.

have you checked the earthing continuity-if it's this other bulbs may also partly light when brakes used
otherwise-
Check continuity of live from center to lh & rh lights and/or is there a live at those lights

Posted on May 03, 2009

  • 1 Answer

SOURCE: How do I replace the Rear Brake light bulb of 2001 Toyota Sienna?

I have a 2001 Sienna and have had to replace most of my tail light bulbs.

The bulbs that are mounted in the fender (wrap arounds) have acess panels in the van's interior that easily pop out and expose the back of the light assembly.

However, the bulbs that are found in the lift gate are a different matter. You have to remove the whole interior panel to the lift gate to expose the light assemblies. Go to your auto parts store and get a tool to help pop out the plastic retainers from the lift gates metal frame. Don't force the retainers out. Go slowly and gently so that you don't damage the interior panel. If you are really gentle you might even get to reuse the retainers.

Good luck!

Posted on Jul 01, 2009

  • 28 Answers

SOURCE: 2003 Toyota Highlander.The brake light on the

Replace the right rear brake lamp. The bulb possible use two filaments one for brake and tail light. One burnt out filament in one bulb.

Posted on Nov 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Only rear driver side brake light will not work when braking need help


Pastor Norman, Pastor Dave here.
Since you already replaced the left rear brake light bulb and that didn't help, please take that bulb socket out again as you did before, and find a way to test the bulb contact for electricity when the brake lights are on. You should get 12 volts out of the "hot" metal contact.
If the other two lights are on, and you have no current in the socket, you either have a bad socket, or a broken wire somewhere.
One way is to go back a few inches and skin off the insulation of the brake light wire and see if there is current back a few inches from the socket. Cover with tape when you finish.
If you decide to cobble a solution, you could run a good wire from the other brake light that works and splice it in to the dead wire.
Be Blessed.

Jan 23, 2013 | 2007 Toyota Corolla

1 Answer

No turn signals, 1 driver brake light bad, ABS light on. 2002/2003 CVPI


Sounds like you have 'ground' issues. Apply the brakes using a broom stick or more apropriate tool so that the brake lights are activated. Then go to the brake light that is not bright enough. using a test-light with a sharp pointed probe, poke the ground wire close to the bulb (usually a black wire) make sure the test light is attached to a grounded bolt. if the brake light gets brighter with ground added, you need a new ground wire. Splice it in to the existing wire & attach it to a bolt. Lights should work better with proper ground. (each bulb has a positive post & neg. post, don't add ground to the side with power coming through it from Battery (+)(red light on test light) - probe wires FIRST with test light to find (+) POS. Hot wire, and leave that one alone.

Aug 09, 2012 | 2003 Ford Crown Victoria

1 Answer

Hi on my 03 chevy suburban my brake lights r some timey i think i know the problem but not sure can someone help me figure this out thanks also where is the brake light switch located on my truck


Well your brake light switch is usually located under the drivers side dash area around the brake pedal if not attached. As far as the lights go, you will have to clarify your problem. sorry





Nov 16, 2010 | 2000 Jeep Grand Cherokee

3 Answers

2002 Jeep Grand Cherokee - Brake lights not working properly. With lights off Driver side no brake light when brake is engaged. With lights on and all rear lights on, engage brake - no driver brake light...


The problem is that the tail lights, light bulbs get too hot and melt the plastic where the bulb socket goes into the lens assembly. On the lens assembly you will see one to three metal tabs where the socket fits into. Lift up the tab a little bit with a screw driver and place a small amount of either metal or plastic underneath the tab so it will get a good connection. It will fix the problem.

Nov 27, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Light brake doesn't work-light on ant-lock brake


you need a rear left circuit board. they come with new lights, and is generaly inexpensive20-30 dollars

May 24, 2009 | 2003 Pontiac Montana

1 Answer

Cluckin in front end


The noise from the front end is probably a bad ball joint. It is possible that it is a tie rod end also.

If the car is supported on jack stands, you should be able to move the wheel around and see where the problem is.

The brake light could be that you are low on brake fluid or there is a problem with your front or rear brakes.

You should have this looked at right away. It is possible that you only have front or rear brakes working at this time and if the other fails, your vehicle will not stop.

If you need more help, post a comment and I will get back to you.

Thanks,

Tim


May 08, 2009 | 1992 Honda Accord

1 Answer

Passenger side rear brake light is stuck on


let me guess..........its a volkswagen! you need to check the brake switch located under the brake pedal.

Jan 22, 2009 | 1983 Cadillac Seville

Not finding what you are looking for?
Cars & Trucks Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...