Question about 2002 Buick Rendezvous

Open Question

BUICK RENDEZVOUS WIPER ARM REMOVAL

HOW DO YOU REMOVE THE WINDSHIELD WIPER ARMS? 2007 RENDEZVOUS

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: How do I remove my wiper arms on my 91 Buick Century?

If I remember correctly if you lift the wiper arm and push this clip in it will hold the wiper up and also release it from the transmission. You will have to wiggle the arm to get loose.

Good luck.....

Posted on Mar 22, 2009

Ad
  • 1129 Answers

SOURCE: 2003 Buick. The pass side wiper stopped working,

the arm mechanism has a clip that pop off get a new clip and remove the access panel and move the arm over to the access area put the arm back into the hole socket and reattache clip , not the easiest repair but with a long pair of needle nose pliers you should have a better chance to complete repair. Some cars to access the arm the wiper motor must be disconnected and pulled out slightly then move wiper over and reattache pin arm into lever hole nstall clip.

Posted on Jul 08, 2009

emissionwiz
  • 79186 Answers

SOURCE: wiper problem buick rendezvous 2002, no power too

the wiper is controled by the body control module, u will need the dealer to test this module for proper functionb.

Posted on Oct 30, 2009

  • 4088 Answers

SOURCE: 2000 Buick Century, Spavinaw, OK, December 26,

Remove the wiper arm and check the serrated hub to see if it sheared a pin holding it to the shaft. If it is ok, then you may have a broken/loose part in the linkage. Good luck!

Posted on Dec 26, 2009

pcdj64
  • 1150 Answers

SOURCE: DRIVERS SIDE WINDSHIELD WIPER JUMPS OFF WINDSHIELD

take the wiper arm off, look at the spline for the arm and the car and see if either is stripped

Posted on Sep 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace windshield wiper motor


Remove the wiper arms, remove the plastic cover under them,look for screws. Unplug the motor. pry the linkage off the motor rod. Remove the motor bolts and reinstall.

Apr 22, 2016 | 2006 Buick Rendezvous

3 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

How to replace a front windshield wiper motor?


You need to pop your hood up, remove your windshield wiper arms but make sure you mark the position of the arms marking on the arm and arm attachment for re-installation alignment, Remove rubber seal and plastic screws (Phillips head), remove windshield wiper water line from left side, then carefully remove plastic cowl. Under neath will be your wiper arms and motor. You can remove all 8 mm bolts and then remove whole plastic cowl and deatach the wiper motor. Installation is in reverse order of removal.

Oct 14, 2013 | 2002 Ford Windstar Cargo

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

Removing windshield wiper assembly ford excursion


Wiper Pivot Arm Removal and Installation
  1. Lift the windshield wiper pivot arm to the full upright position.
  1. Remove the windshield wiper pivot arm.
    1. Release the locking tab.
    1. Remove the windshield wiper pivot arm.
52fed05.gif
  1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
    To install, reverse the removal procedure.

Jul 02, 2009 | 2005 Ford Excursion

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

1 Answer

The wiper blade connection has released from the wiper blade motor bar that controls the wipers movement. You can hear the motor working but the arms have been disengaged.


please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.
  1. Turn the ignition switch (11572) to the on position.
  1. Turn the windshield wiper (17500) on.
  1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.
  1. Remove the windshield wiper pivot arm.
    1. Remove the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the windshield wiper pivot arm.

  1. Raise and support the hood (16612).
  1. Remove the cowl grille seal.
NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.
  1. Remove the LH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the LH cowl grille.
6a042b2.gif
  1. Remove the RH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the RH cowl grille.
bfba69b.gif
  1. Remove the mounting arm and pivot shaft.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the mounting arm and pivot shaft.
8169c1e.gif

Mar 14, 2009 | 2000 Ford Expedition

2 Answers

Cant take off the windsheild wipers


Here is the procedure to remove the wiper motor. It says to remove wipers by removing the nut covers then remove the wiper nuts. Is this what your talking about?
If your talking about the wiper arms they just pop off at the swivel.
Use this link for info on removing blade assy.
http://www.autozone.com/az/cds/en_us/0900823d/80/04/f8/26/0900823d8004f826/repairInfoPages.htm

Wiper Motor
Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the wiper pivot arm nut covers.
  5. Remove the nuts and the wiper pivot arms.
  6. Remove the cowl top vent panels.
  7. Remove the four bolts, wiper mounting arm and wiper pivot shaft assembly.
  8. Disconnect the electrical connector.
  9. Remove the bolt and the windshield wiper motor operating arm from the motor.
  10. Remove the three bolts and remove the windshield wiper motor.
  11. To install, reverse the removal procedure.

Jan 28, 2009 | 2005 Ford Taurus

Not finding what you are looking for?
2002 Buick Rendezvous Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...