Question about 2008 Ford Expedition El

Open Question

Interior silver dash trim removal 2008 expedition

Silver trim removal

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: rear hatch will not open,how is the interior trim

look for any plugs that may be covering screws around outside edge, as well as obvious screws, then the rest will probably be push/pull clips. Usually a quick **** will release them.

Posted on Feb 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't find my kill switch on my expedition 2003


Inertia Fuel Shutoff (IFS) Switch Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the LH rear interior trim panel.
  1. Disconnect the inertia fuel shutoff (IFS) switch electrical connector.

Jul 11, 2015 | 2003 Ford Expedition

1 Answer

Interior light delay


Same for both doors? If not, I'd check the switch(s) on the drivers door (may be more than one), or may be just one that has multiple contacts and the ones for the lights may be faulty.

Jul 01, 2017 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Heater cor is leaking how do I change it?


REMOVAL




  1. Disconnect the battery ground cable.
  2. Drain the radiator. Refer to: "Engine, Cooling and Exhaust : Cooling System : Service and Repair" See: Service and Repair
  3. Remove the instrument panel. Refer to: "Body and Frame : Interior Trim : Dash Board : Service and Repair" See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair




  1. Compress the holding tabs and disconnect the heater water hoses at the heater core.




  1. Remove the A/C plenum demister adapter.
  1. Remove the screw.
  2. Remove the A/C plenum demister adapter.




  1. Disconnect the vacuum line.




  1. Remove the heater core bracket.
  1. Remove the two screws.
  2. Remove the bracket.




8 Remove the plenum assembly top.
  1. Remove the 13 screws.
  2. Remove the plenum assembly top.
  1. Remove the blend door assembly from the case.




  1. Remove the heater core.
INSTALLATION








  1. To install, reverse the removal procedure.
NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

Dec 17, 2012 | 1997 Ford Expedition

1 Answer

2008 chevrolet interior door handle repairs


There is a repair kit for you truck. The part that is broken is the metal piece. If you go through GM you have to buy a brand new interior door trim panel because the door handle part is attached to it. Otherwise I found a company that offers a repair kit that just repairs the broken part. Plus is cheaper then buy a whole interior door trim part. Total Automotive GM Truck SUV Interior Door Handle Repair Kits

Apr 25, 2012 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

2008 GMC Acadia manual liftgate will not open. Is there a way to bypass the electronic switch to get it open and replace the switch or latch?


{: ) Liftgate Access Plug is located at the bottom center area of the liftgate trim panel.
From inside the vehicle lower the second and third, if applicable, row seats.
Use a small flat-bladed tool to remove the access plug from the liftgate lower interior trim panel. It is like a round and smooth plastic grommet.
Push on a silver lever located on the right just through the access hole to unlock the liftgate.
Open the liftgate from the outside of the vehicle using the exterior handle.

Apr 06, 2011 | 2007 GMC Acadia SLE

1 Answer

Remove door panel


Expedition Trim Panel Removal

NOTE The door glass must be completely raised.
  1. Remove the window control switch plate.
  2. Remove the door handle bezel.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  3. Remove the two bolts and three screws, and remove the door trim panel.
  4. Remove the finish cover to access the two center screws.
  5. Disconnect the electrical connectors.

    zjlimited_454.jpg

    Fig. Expedition - Trim Panel Screws shown

  6. Remove the door handle bezel.
  7. Use service notch.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  8. Remove the two bolts and three screws, and remove the door trim panel.
  9. Disconnect the electrical connectors.

    zjlimited_455.jpg

    Fig. Navigator - Trim Panel Screws shown

  10. Position the water shield aside.
  11. If equipped, disconnect the lock cylinder rod.
  12. Disconnect the exterior door handle actuating rod.
  13. Remove the bolts and position the front door latch aside.
  14. Disconnect the electrical connectors.
  15. Release the interior door handle cable and remove the front door latch.
  16. Position the cable cover aside.
  17. Release the conduit and the interior door handle cable.
  18. Release the locking tab and remove the front door lock actuator.
  19. To install, reverse the removal procedure and note the following:
    1. Tighten the door latch screws to 80 inch. lbs. (9 Nm).

This procedure is followed to check and fix door locks.

Hope helps.

Jan 12, 2011 | 2001 Ford Expedition

1 Answer

Put fual pump in will not start were is the reset button


Inertia Fuel Shutoff (IFS) Switch Removal & Installation There is no 6.4L engine, it's a 5.4L engine, right?

Also, for the To Remove:
  1. Disconnect negative battery cable.
  2. Remove right rear interior trim panel. ford-05-00-3949.gif

  3. Disconnect IFS switch connector.
  4. Remove IFS switch bolts.
  5. Remove IFS switch.
To Install:
  1. Install IFS switch.
  2. Install IFS switch bolts.
  3. Connect IFS switch connector.
  4. Install left rear interior trim panel.
  5. Connect negative battery cable.
prev.gif next.gif

Jul 08, 2010 | 2000 Ford Expedition

1 Answer

How to get to the stock subwoofer, in 200 eddie bauer expedition


It should be mounted on the passenger back. you will have to remove the rear quarter interior panel, The trim where the hatch locks and around the trim where the hatch meets the rear. once the trim is removed you can access the sub, it is bolted to the car and plugs into the factory amp, which is located right in front of the sub. After taking the bolts out, the sub will come out.

Dec 26, 2009 | 2000 Ford Expedition

1 Answer

* * * Removal of Interior Trim Panel * * *


There are 2 finish covers on each side,looks like the one on the left is directly over ash tray?
You have to remove these 2 covers and there will be a screw located there. Remove these 2 screws remove the upper center finish panel by pulling outward to release the panel retaining clips.

Jan 30, 2009 | 2008 Ford F 250 Super Duty 4WD

2 Answers

I need to replace passenger side mirror on 97 ford expedition


Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman

Dec 27, 2008 | 1997 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...