Question about 1995 Honda Accord

1 Answer

How do i install a driver window for a 95 Honda Accord EX 2 door?

I replaced the motor and regulator but i can't get the NEW glass put inside the door. The plastic piece on the top right hand side how does it go into the groove?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

If you take the channe out rubber that holds in the glass/ put the glass first in then get like glass cleaner spray in the groove sthen you slide the run channel back into the window and slide it down/ that piece should thengo into glass and hold it into the run channel. if you have any questions let me know Please rate my response thank you very much

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove broken side rear glass 95 honda accord


94-97 Honda Accord Rear Side Window Install - YouTube

? 6:00
https://www.youtube.com/watch?v=Cgn0EmuY9NU
Jan 8, 2013 - Uploaded by Function Factory
94-97 Honda Accord Rear Side Window Install ... How to fixreplace install a broken power window regulator ..

Nov 18, 2015 | Honda Cars & Trucks

1 Answer

My 1995 Honda Accord power windows just stopped working. Drivers side is fine. It is the rear 2 windows and the front passenger side will not go up. Checked fuses they were all fine. any suggestions?...


It could be the motor of the power windows.

  • Troubleshoot
    • 1

      Check the fuses and switches. Your owner's manual and fuse-box cover have fuse and switch diagrams. Look for the power window relay and power window motor labels. Tug out the fuse and check it for damage. Check the switches for deterioration or abnormalities. You can get a new fuse or switch at an auto parts store or super center and easily replace it.

    • 2

      Get out your tool box if you've eliminated fuses and switches as the cause of the problem. Now you have to remove the door panel to get a better look at your window's power source. For the driver's side and passenger-side doors, remove the door pad and inner moisture barrier. Use an upholstery-removal tool to help pry the panel off. The rear windows require that you remove the two center channel screws at the top of the door frame and two lower bolts in the bottom of the door. Check under the weather stripping if those bolts aren't evident.

    • 3

      Lower the window until the glass bolts are visible. Use the 10mm socket wrench to remove the bolts in the large and smaller access holes. Standing at an angle inside the door, tip the glass gently toward the outside of the door. Pull it out and set it in a secure place.

    Inspect the Motor and Regulator
    • 1

      Access the regulator by removing the front channel and regulator mounting bolts. Older models have additional roller bolts.

    • 2

      Use a digital voltage meter to test regulator power before completely removing it. A reading of less than 12 means you have a wiring or switch problem. Recheck the fuses and switches. A reading of 12 means your wiring and switches are getting power to the motor, so the motor is inoperative for another reason.

    • 3

      Remove the motor and regulator. Wear protective gloves and keep your hands clear of the regulator gear spring. You can expect it to snap abruptly on removal.

    Install New Power Window Motor and Regulator
    • 1

      Use oil to grease the roller guides and sliding surfaces of the regulator after removing all the parts. Confirm that the breather pipe is in position to keep water out of your new motor.

    • 2

      Advance the new regulator gear with your gloved hand. Use the collar and mounting bolt to secure the new motor in place. Replace the front door run channel.

    • 3

      Slide the window glass back into the door. Advance the regulator with the power window control in the door until the glass mounting bolt holes line up with the access holes. Replace the window mounting bolts.

    • 4

      Test for smooth operation of the window. The window should move up and down easily and form a tight seal when closed. Tighten or loosen window mounting bolts as needed.

    • 5

      Replace the liner and door panel. Dispose of the dead motor.

  • you can read more: How to Fix Power Windows in a Honda Accord ' eHow.com http://www.ehow.com/how_4520901_fix-power-windows-honda-accord.html#ixzz1Jj3YBoi0

    Apr 14, 2011 | 1995 Honda Accord

    1 Answer

    New power window regulator installed, now window goes up to top then comes back down half way and stops. How to adjust?


    It is important to learn how to fix a Honda Accord window if you have an older Honda Accord. Although the Honda Accord is renowned for being a durable vehicle, the electric window motor regulators in older models can wear out over time. This is noticeable when you hear sounds coming from the window when you attempt to use it but the window won't move. But don't worry, you can use these steps to fix a broken window in your Honda Accord.

    To fix a Honda Accord window, you will need:
    • A Phillips screwdriver
    • A flathead screwdriver
    • A wrench set
    • A black marker
    • Masking tape
    • A new Honda Accord electric window regulator
    1. Remove the screws securing the door panel from the inside of the vehicle. These screws are beneath the arm rest. Release the door panel by prying it away from the front of the door. Work your way back by prying off the top and sides of the panel and the back of the panel.
    2. Remove the clips holding the door panel using a flathead screwdriver to pinch them together. Remove the panel by sliding it upward and away from the door.
    3. Remove the two bolts securing the window to the regulator. Note the position where the bolts secure the windows. When you re-install the window you will need to adjust them similarly. Making a small mark on the window with a black marker is a good way to easily keep track of the correct position.
    4. Lift the window directly up and remove it from the car door. Secure it using masking tape if you prefer not to remove it completely.
    5. Remove the bolts securing the window motor and guide. Remove the window motor and guide and set them aside.
    6. Remove the regulator from the power window motor assembly. Dispose of the old regulator and install the new unit.
    7. Re-attach the window motor and guide to the door by following the removal instructions in reverse. Test the new window regulator by turning on your ignition switch and moving the window up with the electric switch.
    take it back apart somethings not tight

    Dec 07, 2010 | 2004 Honda Accord

    1 Answer

    How to replace a electric motor for power window in 1994 honda accord


    How to Replace a Window Regulator (with Motor)
    (DIY Complexity: Moderate / DIY Time: 2.8 hours)

    Parts:
    1. Window Regulator

    1ed581e.jpg


    Tools:
    1. Screwdriver
    2. Trim Panel Removal Tool
    3. 3/8 in. Drive Ratchet
    4. Socket Set
    5. Riveter Kit

    Steps:
    Step 1 Remove the door panel by removing the handles and switches. It is required to unscrew or unclip the panel.
    o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
    o Tip: Refer to the vehicle specific service manual if available. There are several fragile plastic clips and hidden screws on the door panel that will break if removed improperly.

    Step 2 Remove the vapor barrier.

    Step 3 Disconnect the glass from window regulator.

    Step 4 Tape the glass to door frame. The glass should not require removal.
    o Tip: Tape the glass out of the way to allow access to the window regulator and window lift motor assembly.

    Step 5 Disconnect the electrical connector from the window motor.

    Step 6 Remove the window regulator mounting bolts. Slide the regulator assembly out through the interior access opening of the door. Remove the motor.

    Step 7 Attach the original motor to the new window regulator and install the regulator assembly. Tighten the mounting bolts.

    Step 8 Reconnect the electrical connector to the window motor.

    Step 9 Install the window back onto the window regulator.

    Step 10 Re-install the vapor barrier.

    Step 11 Re-install the door trim panel and handles/switches.

    Step 12 Test the power window for proper operation by rolling the window up and down in complete cycles for proper testing.
    o Tip: After re-installing a window lift motor and regulator, it may be necessary to re-program it following manufacturer specific instructions. Not following or performing this step may result in improper power window function.


    Hope helps (remember comment and rated this).

    Jun 18, 2010 | 1994 Honda Accord

    1 Answer

    I have a 2002 Honda Accord EX 4-dr sedan. The front driver's side power window motor works (you can hear it), and the window will go down, but not back up. You can hear the motor when pushing the button...


    Hi, the reason you hear the motor running but the window wont go back up is because the window regulator is bad. you will need to go to a parts store and get a replacement. you can get a replacement at Advance Auto Parts for $72.99. the part number is 741-766.

    May 18, 2010 | Cars & Trucks

    1 Answer

    How to install 95 vw jettta front driver side window regulator


    1.remove the door trim paneland the plastic watersheild.
    2.this u can skip if u can keep the glass out ur way. but remove the glass.
    3.disconnect the electrical connector from the reulator motor.detach the cables from the inside handle.
    4.remove the bolts holding the regulator/motor assembly.
    5.installation is the reverseof removal.lubricate the rollers and wear points on the regulator with white grease before installation.
    6.wear gloves when working inside the door openings to protect from sharp metal edges.
    hope that helps if you need more help let me know bertman285@hotmail.com

    Oct 06, 2009 | 1995 Volkswagen Jetta

    1 Answer

    How to install driver side window regulator


    1. Take door panel off by prying off with srew driver moldings for outside mirror,around lock,and door handle, then pry up counsel for power locks, windows, and mirror adjustment and disconnect plugs. Remove three screws located behind arm rest handle, inside where counsel was removed, and bottom middle of door panel. Lift panel and pull slighlty towards you. Disconnect courtesy light, and wire to speaker. This may sound like alot but it goes pretty fast. 2. Peel away plastic and loosen window glass clamps (explaination from above, which are accessable when window is in up position). 3. Disconnect wire to motor, and remove 6 bolts holding guide rails and motor. Lift rails slightly to release from little hangers, which come in handy when putting new one in. 4. You should be able to remove entire window regulator at this point. Surprisingly the window stayed in up position when regulator was removed. 5. Before installing new regulator loosen window glass clamps. Install new by first setting guides in place by using the little hangers. Bolt guides and motor, temporarily connect power window switch and carefully raise window regulator until clamps are resting in place under window glass, tighten clamps. Test before putting panel back on.

    Jul 30, 2009 | 2000 Mitsubishi Galant

    1 Answer

    My driver's side window has fallen into the door. I have a 2000 Honda Accord. The motor on the auto window is still running.


    Possible faulty window regulator. Pull panel and check if window guide(this holds the glass to regulator) on the regulator is damaged. Replace guide or regulator if damaged. Hopefully this helps

    Jul 20, 2009 | 2000 Honda Accord

    1 Answer

    Power window problem. engauges then disenguages


    Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
    svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
    1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
    1. Remove inside door belt weatherstrip.
    1. Remove front door window glass (21410) as described in this section.
    1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
    1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
    1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
    1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
    1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

      Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


      a9ef3ee.gif

    Installation
    NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

    1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
    1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

      Install four rivets to retain front door window regulator to door inner panel.
    1. Install window regulator equalizer arm bracket.
    1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
    1. Install inside door belt weatherstrip.
    1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
    1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


      Door Glass and Regulator
    ac1dac5.gif

    Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

    Apr 13, 2009 | 1997 Ford Windstar

    1 Answer

    Replacing 99 Accord window regulator


    Pull off door panel speaker and switches. lower the window to where you see the two or four 10millimeter that connect scissor mechanism to the window. Prop window all the way up and put a door stopper to prevent the window from falling down. Unbolt window motor, unplug window motor, and unbolt eveything else in the door. Pull it all down and out through the bottom largest whole, lay flat on ground the entire indoor mechanism, out where you can see it on the floor. Take a pic with camera, and proceed to swapping regulator, intallation is same as removal. Good Luck

    Dec 28, 2008 | 2000 Honda Accord

    Not finding what you are looking for?
    1995 Honda Accord Logo

    331 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...