Question about 1999 Hyundai Accent

3 Answers

Clutch peddle goes to the floor - 1999 Hyundai Accent

Posted by on

  • vincedangona Jan 28, 2009

    were might the slave cylinder be located? if the motor points to the right side of the please dont tell me its in the left rear of the motor cause as far as i can see the puddle comes from this area

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like you have a bad slave cylinder my truck just done the same thing. It is either located inside the transmission or on the outside of the transmission

Posted on Mar 30, 2012

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 24 Answers

Check the fluid in clutch master cylinder res. if low add then pump the clutch pedal several times then get out of car and look for fluid leak some where on side of trans.you are loofing for the slave cylinder its usually the first to go.

Posted on Jan 28, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Do you mean that stays to the floor because the clutch peddle has to reach the floor. If that is what you mean then probably you need a knew clutch or if it is hydraulic maybe it reflling and dicomression.

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch peddle is low to the floor


Sounds like you need to adjust the linkage or possibly change the cable. You might need to change the clutch and pressure plate but that doesn't seem likely. I would start with the linkage.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Clutch peddle wont go all way to the floor


Clutch fluid level low, bad slave cylinder, bent linkage

Sep 22, 2013 | 2003 Hyundai Tiburon

1 Answer

How do i bleed clutch on 2000 trans am ws6 ram air


I\'m assuming this is the one with the 5.7L LS1 V8. Ok, bleeding the clutch is real no different than bleeding your brakes. Locate our slave cylinder.(Not the reservoir) In most cases, it\'s best to start with a gravity bleeding. Make sure the reservoir is full, loosen the bleeder on the slave cylinder, until you have a steady stream coming out. Then tighten the bleeder, and check the peddle.SUCKAUTION**** MAKE SURE THE BLEEDER VALVE IS TIGHTENED AND CAP IS ON THE RESERVOIR BEFORE YOU TOUCH THE CLUTCH PEDDLE!!! AS MISSING THIS STEP WILL **** UP AIR INTO THE LINE.Step 2, have a friend sit inside the car, and continuously pump the clutch(like bleeding brakes) about 10 pumps should do it. Have friend hold the peddle to the floor and announce that it is to the floor. ***They must hold the peddle to the floor*****while they are holding the peddle, loosen the bleeder valve until fluid comes out. repeat process until no micro bubbles come out, just clean fluid. Finally, remember to top off your fluids after bleeding, as you will naturally loose some in the process. Hope this helps. ^^

Mar 27, 2013 | Cars & Trucks

1 Answer

I own a 1995 Audi 90cs. My clutch peddle started being dead tell half way down then got preshure. Now there is no preshure and the peddle sticks to the floor. There was no slipping in the clutch so I


You need to replace the clutch slave.....Ii recently did mine, after the installation it was stuck too.......the way I fix it was I had a friend pumping the clutch by hand while I bleed it under the car, it took about 15-20 minutes before it got hard again.
Good luck!

Aug 01, 2012 | 1995 Audi 90

1 Answer

The clutch peddle went to the floor when i pushed the clutch peddle in


Check the floor by the clutch peddle if it is wet (you may need to look at the very top of the peddle)than you problem is the clutch mastercylinder

Jan 31, 2011 | 1994 Nissan Pickup

2 Answers

2001 nissan maxima clutch problems


check the mechanical leakage at the clutch housing for binding and wear.

Jun 12, 2009 | 2001 Nissan Maxima

1 Answer

2000 cavalier clutch pedle goes to floor when pushed and stays there, clutch not working no pressure


You are going to have to replace the master and slave cylinders for the hydraulic clutch, the seals have failed in the slave, but from past experience they should always been replaced as a pair.

Oct 12, 2008 | 1998 Chevrolet Cavalier

2 Answers

CLUTCH PEDDLE GOES TO FLOOR AND I CANT SHIFT


leak in cylinder or line of clutch assembly or no oil

Jul 28, 2008 | 1998 Jeep Wrangler

Not finding what you are looking for?
1999 Hyundai Accent Logo

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...