Question about 2003 Ford F150 Regular Cab

1 Answer

Rear Brake Squeal. 2003 F-150 4Wd

Replaced pads, Rotors on all four wheels. getting right rear brake squeal at the initial use of brakes at slow (traffic, parking lot) speeds. Have tied removal and cleaning, sanding pads, after market squeal inhibitors, etc. Seems only to be affecting Right Rear.

Posted by on

  • 2 more comments 
  • shagstr Jan 28, 2009

    Not cheap pads, but not the most expensive either.

  • shagstr Jan 28, 2009

    I'll try that, but why only one wheel is an issue?

  • Anonymous Mar 19, 2009

    I have this same problem, Nobody seems to know how to fix it..Any ideas?

  • mlusk May 11, 2010

    did you use cheep pads because I have found the cheaper pads tend to squeel.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 24 Answers

Change to a ceramic pad not semi metallic

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My brake pads have been changed and the wheels continue to squeal. They rattle and squeak when driving and braking


it just sounds like a poor quality job...the proper way to do a brake job is a high quality set of front pads such as a bendix or raybestes gold line pads,, then have the front brake rotors machined an a amco brake lathe or even better a on the car brake lathe. make sure all brake caliper hardware is properly cleaned an lubercated or replaced with new hardware....then have the rear brakes adjusted( adjust only if ur car has rear drum brakes...rear disc brakes r selfadjusting

Jul 16, 2011 | 2003 Chevrolet Impala

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

3 Answers

I've had the rotors and pads replaced on my 2006 Toyota Tacoma Pre-runner and the front brades brakes still squeal when braking lightly. I have switched to the premium pads and rotors. What else can be...


Are the leading edges on the brake pads bevelled at an angle or are they flat on the brake rotors? There seems to be a problem with Japanese brake rotors (something about the harmonics) and they will sometimes squeal (even with new brake rotors and pads) if the leading edges on the brake pads are not bevelled at an angle. Most of the auto repair shops that I have worked at will only install bevelled edge brake pads on foreign vehicles, especially if they are Japanese imports. If the brake pads do have the edges bevelled then most likely dust has found its way between the brake pad and the brake rotor, and brake dust contamination is the #1 reason for a brake squeal come-back, and that is why a good repair facility will always clean the entire brake assembly including the backing plate for the brake rotor. Also, the brake caliper guides should be able to slide freely in and out of the brake caliper but they should not be sloppy either, and the brake caliper guides should be lubricated with a synthetic brake caliper grease only. The caliper guides should be able to slide freely in the brake caliper and if they do not the brake will not properly release.

If the brake calipers have phenolic (plastic) brake pistons then get rid of them for brake calipers with metal brake pistons.

Here is an image of the two different brake pad designs.


d8c9f51.jpg

Aug 03, 2010 | Toyota Tacoma Cars & Trucks

2 Answers

Brake squeal


You, Probably will, Brake Squeal is NOT a new problem.
Disc brake's have been Squealing since, They, became
factory installed on chevrolet in 1971. Before, that they,
were a option. In 72 they even had a bulleton how, to
FIX it. And, no it didn't work.
With That said, Any time you replace Brake pads you,
should always re-surface the Rotors.
Why? First you may start to notice a pulsation as the
pads ware (sometimes! ) The best way to avoid, brake
squeal is to manchine the Rotors put, the blue membrain
sealent on the back side of the pads. And hope that works!!
Some brakes Pads squeal JUST SQUEAL??
You, Could do the same Brake job the same as you did
this one and, they may NOT Squeal.WHY, I WISH I NEW. They
sell all types of STUFF to stop Brake noice DON'T waste your $$.

Jan 31, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

Rear brakes (driver-side) squeal after replacing rotors and pads


you need to grease the metal clips at the top and bottom of the pads (dont get grease on the rotor or pad though) and also spray some "disc brake quiet" on the back of the pads. it comes in a red can and the spray that comes out is like sticky red paint. do those 2 things and the squeals will be gone.

May 30, 2009 | 2006 Hyundai Tucson

1 Answer

Replaced brake pads, extreme squeal resulted


Pads will reproduce sound just like a needle on a phonograph. Hard linings will accentuate this. Have the rotors re-surfaced and finished with a non-directional pattern(I make a quick pass with a D/A sander over surfaces while still on the lathe) Generally this will help.

Mar 30, 2009 | 2005 Jaguar XKR

1 Answer

Constant squeal in brakes,


Front or rear brakes?
Make sure the rotor isn't contacting the backing dust plate.
Make sure the brake pad slider clip/clips are not contacting the rotor.

Mar 28, 2009 | 2006 Hyundai Sonata

2 Answers

2005 Dodge Durango Front Brake Squeal


Did you buy factory pads or get cheap aftermarket pads? If aftermarket did you get the ceramic? The cheap aftermarket ones tend to squeal pretty bad. Like the last comment on here, you should have your rotors turned whenever you change the pads.

Jan 13, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
2003 Ford F150 Regular Cab Logo

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...