Question about Cars & Trucks

Open Question

2000 jeep cherokee coil pack replacement - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Jeep Hesitates. P0303 code

Check the cylinders Commpression. over 115 psi is good, 120 psi is normal.

Posted on Sep 17, 2008

Ad
  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

  • 1118 Answers

SOURCE: 1998 jeep cherokee no power to ignition coil

chk. ignition switch, and fuses.

Posted on Feb 08, 2009

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

  • 1 Answer

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 grand cherokee misfire cyl 1 replaced plugs and coil pack any solutions


Plug wires or defective coil pack after market electronics come bad from the store some times also could be pluged or bad fuel injector try some good fuel cleaner like lucas

Dec 19, 2010 | Jeep Grand Cherokee Cars & Trucks

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Jepp Cherokee 2000 4.0 L 123K miles, cylinder #6


try changing your crank senor. Get part from the dealer... My jeep was misfiring and changed OEM part and jeep rides good.

Apr 27, 2009 | 2000 Jeep Cherokee

2 Answers

2000 grand cherokee #7 Cylinder not fireing


replace the coil pack... to confirm this pull spark plug leads off the coil pack one at a time.... note whether the idle changes. the spark will actually arc and you can hear it. if one of the plugs does not have this arcing... the coil pack is at fault.

Please take a moment to rate this solution.. thanks

Apr 19, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Location of the sparkplug wires in a 2000 jeep grand cherokee


If you have the distributorless ignition, you wont have any spark plug wires. This is because the ignition coil packs sit directly on top of the spark plugs. The spark plug boots are connected directly to the ignition coil pack.

If you stand in front of your vehicle open the hood and look to the left side of the motor, just around at the bottom of the valve cover, you'll see a series of three humps. Those are the coil packs and they are held in by four bolts I believe and if you take those out and pry up on the long coil pack, it will come loose from the plugs and then you can change them out.


Jan 03, 2009 | 2000 Jeep Grand Cherokee

2 Answers

2000 jeep cherokee sport 4.0


I believe that year had distributorless ignition, instead it uses a form of coil on plug ignition system.

If you open the hood, stand at the front of the vehicle. Look to the left side of the engine, around the bottom of the valve cover (The valve cover is where the oil fill cap is. The oil fill cap is on top of the valve cover), at the bottom of the valve cover on the left side you will see a series of humps. Those series of humps is the coil packs, the coil packs are all in one long piece held down by three or four bolts.

Take out those bolts, gently pry up at the ends of the coil pack and it will eventually come out. You'll see on the bottom side the spark plug boots are attached to the coil pack. After you get the ignition coil pack off, you will see the spark plugs under where the coil pack came from, the boots on the coil pack sit directly on the spark plugs.

Jan 01, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...