Question about 2005 Kia Rondo

Open Question

2007 kia rondo 2.7 eng how to replace timing belt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2007 Kia rondo interior lights stay on when headlights turned on

I had the same problem for months. Finally took it to the dealer. The first time, they diagnosed is as a short in the rear interior bulb, and put in a new bulb. Got it home and still had the same problem.

The second time in, they figured things out. On the dash to the left of the steering wheel is a knob that controls the brightness of the dash lights. But, if this knob is all the way on, it turns on the interior lights and keeps them on. Just had to turn this knob down, and the problem was solved!

Posted on Apr 19, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: 1999 kia sportage timing marks

dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif

  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Posted on Jul 26, 2009

  • 4044 Answers

SOURCE: change front rotors kia rondo 2007

Remove the tire, remove the brake calipers, 2 bolts on back side of rotor, remove the carter pin that retains the bolt position if equiped, remove the center nut. When you pull the rotor off watch for a set of bearings to drop out. To install the new rotor reverse the process.

Posted on Sep 17, 2009

  • 67 Answers

SOURCE: engine light came on kia 2007 rondo

you need to have the code read to see what it is most auto parts store can do that for free that will help use tell you what it is

Posted on Mar 04, 2010

  • 111 Answers

SOURCE: were is the fuel filter

IT IS INSIDE THE FUEL TANK . IT IS MADE INSIDE THE FUEL PUMP IT IS SERVIECABLE AND RECOMMENDED EVERY 30K . THERE IS A ACCESS TO THE TANK UNDER THE SEAT THERE IS A FEW SCREWS THAT HOLD IT A COVER DOWN REMOVE THIS AND YOU CAN ACCESS .
REOMOVE FUEL PUMP AND TAKE APART THE ACTUAL PUMP SEATS INSIDE THE FILTER .IF YOU TRY TO DO IT YOURSELT BE SURE NOT TO FORGET ANY O RINGS THEY TEND TO STAY IN THE OLD FILTER WHEN REPLACING AND IF YOU DONT SWAP OVER THE VEHICLE WILL NOT START

Posted on Jan 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the spark plugs on my 2007 Kia rondo lx v6


REPLACEMENT
1. Remove the ignition coil connector (A).
2. Remove the ignition coil.
3. Using a spark plug socket, remove the spark plug.26379325-trdzh3npzosxk4r5ena25aw0-5-0.jpg

Nov 30, 2016 | 2007 Kia Rondo LX V6

1 Answer

Where is purge valve on 2007 kia rondo


I got p2187 on my 2007 kia rondo

Oct 28, 2016 | 2007 Kia Rondo

1 Answer

TPMS of KIA Rondo 2007


the only solution on that is to replace it. it is'nt be recalibrated. the instruction are in the operating manual that is sent with the car.

Feb 23, 2012 | 2007 Kia Rondo LX V6

1 Answer

Need a belt routing diagram for a 2007 kia rondo 2.4


Need drive belt diagram on a 2.4 Kia rondo

Feb 18, 2011 | Kia Rondo Cars & Trucks

3 Answers

Were is the fuel filter located on a 2007 Kia Rondo


IT IS INSIDE THE FUEL TANK . IT IS MADE INSIDE THE FUEL PUMP IT IS SERVIECABLE AND RECOMMENDED EVERY 30K . THERE IS A ACCESS TO THE TANK UNDER THE SEAT THERE IS A FEW SCREWS THAT HOLD IT A COVER DOWN REMOVE THIS AND YOU CAN ACCESS .
REOMOVE FUEL PUMP AND TAKE APART THE ACTUAL PUMP SEATS INSIDE THE FILTER .IF YOU TRY TO DO IT YOURSELT BE SURE NOT TO FORGET ANY O RINGS THEY TEND TO STAY IN THE OLD FILTER WHEN REPLACING AND IF YOU DONT SWAP OVER THE VEHICLE WILL NOT START

Jan 12, 2011 | 2007 Kia Rondo LX V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...