Question about 2000 Buick Century

Open Question

Error code C1225 ABS - 2000 Buick Century

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I installed a new computer, it's been flashed, and I cleared all engine codes, Bur have 1 abs code.


Unfortunately no. But if you replace the hub the ABS computer should not see the error anylonger. The ABS computer does a self test at key on, if there is not error to register then it should give the all clear.

Jan 19, 2016 | 2000 GMC Sierra C/K3500

1 Answer

Check engine light is on and diagnatics show the error codes, P0722 and U2108


Definition of Diagnostic Trouble Code U2108 Buick: CAN Bus Error ABS Cadillac: CAN Bus Error ABS Chevrolet: CAN Bus Error ABS GMC: CAN Bus Error ABS Oldsmobile: CAN Bus Error ABS Pontiac: CAN Bus Error ABS Saturn: CAN Bus Error ABS


Definition of Diagnostic Trouble Code P0722 Category: Powertrain Definition: Output Speed Sensor Circuit No SignalNote: This definition of P0722 is applied to all manufacturers

Jun 27, 2015 | Cars & Trucks

3 Answers

What is the C0265 error code


The ABS EBCM anti-lock brake module is failing causing problems with the ABS pump running constantly, also will drain your battery.
  1. Remove the ABS fuse to prevent ABS motor burn out.
  2. You can still drive your vehicle with the module removed.
  3. We recommend covering the exposed surface of the hydraulic control unit with aluminum foil to keep out water and dirt.
Common Failures:
  • ABS Pump Always Running
  • Codes: C0265, C0267, C0268
  • Pump Motor Circuit trouble code
  • Power Relay trouble code
  • Valve Relay Trouble code
  • Dump Valves (solenoids) trouble codes
  • No Communication
  • Intermediate power loss
http://www.myairbags.com/dtc-code-c0265-abs-ebcm-light/
ebcm-abs-control-module-failure-code-dtc-c0265-c0267-c0268-pump-running-y52j5yjvtwyljepizajwhmfx-1-0.jpg

Nov 28, 2014 | 2001 GMC Sierra C3

1 Answer

What is the code c1222 and c1225 means


need to know the vehicle and year at least , lost my mind reading ability years ago !

Jul 18, 2014 | Cars & Trucks

1 Answer

Lights shut off


The C codes in the obd system are chassis codes. Your codes are for solenoid short, ABS short, brake light warning short, wheel sensor short, Right rear speed sensor short.
So with all those codes present, was the vehicle subject to water damage or snow and ice?

Jan 02, 2014 | 1996 Buick LeSabre

1 Answer

99 olds alero abs trouble codes


looks like all 4 brakes need checked..

Dec 27, 2013 | 1999 Oldsmobile Alero

1 Answer

Abs on vr commodore light stays on solutions


Error logs are a great thing. They will help you find intermittent problems and start you off in a general direction of where a problem could be. There is a great level of detail on the justcommodores site on checking error codes logged by the engine management system, but this does not detail anything about the abs system. The abs warning light is not as common as the check engine warning light. Reading through the posts, I haven't found any detail on checking error codes logged by the abs system.

So here it is. For those of you familiar with checking the engine error codes, this procedure is so simple its not funny.

Basically, to check the engine error log, you bridge the 5th (ground) and 6th pins in the ODB connector under the steering wheel.

To check the ABS error log, using the same trusty calibrated paper clip, you simply bridge pins 5 and 12 of the connector.

To find pins 5 and 12, start at the top left hand corner. That is pin one. Going to the right, you count pin 2,3,4 etc. Once you get to the end, jump back to the start of the bottom left level of pins and keep counting. Pin 5 is about halfway along the top row, pin 12 is a little left of the middle in the bottom row.

Reading the error codes is the same procedure (counting the flashes), except now, the ABS light flashes (as opposed to the engine light when checking the engine codes).

The ABS log also uses code 12 firstly, with any errors logged shown after that. If no errors are logged, the 12 will flash again.

Error codes for the ABS error log (VR/VS) are as follows:

12 Diagnostic system operational
21 Right hand front wheel speed sensor fault
23 Right hand front wheel speed sensor continuity fault
25 Left hand front wheel speed sensor fault
27 Left hand front wheel speed sensor continuity fault
28 Wheel speed sensor frequency error
31 Right hand rear wheel speed sensor fault
33 Right hand rear wheel speed sensor continuity fault
35 Left hand rear wheel speed sensor fault
37 Left hand rear wheel speed sensor continuity fault
41 Right hand front inlet solenoid valve circuit fault
42 Right hand front outlet solenoid valve circuit fault
45 Left hand front inlet solenoid valve circuit fault
46 Left hand front outlet solenoid valve circuit fault
55 Rear inlet solenoid valve circuit fault
56 Rear outlet solenoid valve circuit fault
61 Pump motor relay circuit fault
63 Valve relay circuit fault
71 ABS control module internal fault

The above guide has been verified on a VR/VS. Checking the error log on all models prior to VR/VS is the same for the engine log, and I would assume that the same can be said for the ABS log, would be happy if someone could verify this for me.

Sep 21, 2013 | 2005 Mazda Tribute

1 Answer

What is obd2 code c1225 on my 2000 alero


Most likely, the cause is a bad ABS harness. Rarely is it the hub!

Mar 13, 2013 | 2001 Oldsmobile Alero

2 Answers

Traction conrol abs


Try seeing if any of the codes are set off. On your climate control section with the ignition on hold the off and warmer button and the display will cycle through the codes. Could be a wheel sensor I had a c1225 LF sensor. Could also be a problem with the Wheel speed sensor harness see TSB# 0005-25-003. When I called my dealer about this TSB they didn't know anything about it. If you shut off the car and disengage the traction control, in the glove box, do the codes go away?

Good luck

Jun 29, 2009 | 1999 Cadillac DeVille

1 Answer

Trac Off and ABS Lights came on, won't go off


trac control & abs light staying on in dash on pt cruiser 2001 limited
well had same problem with my pt cruiser 2001, firstly there is no need to plug in computer under the dash for pulling abs error codes,
because the problem can be the cracked abs ring on the drive shaft/cv joint,
turn your steering all the way to left and ask your colleague to see if behind the tyre the abs ring is broken or cracked,
it is circular like a bracelete with grooves, then turn the steering to the right and repeat the inpesction,
if the abs ring is cracked then look on ebay or web for pt cruiser abs ring or kia abs ring, should cost about £5-£10 each
and a garage could heat it up with gas and hammer it into the drive shaft/cv joint for you for about £20-£30,
takes about 30min to 45mins, make sure the garage dont heat the cv booth kit rubber next to the abs ring when heating it up.
i heard you can only buy abs ring for front wheels and its not available separately for rear wheels,
so for rear you may need to buy the whole part it comes on
the front abs rings are easily visible when you turn the wheel to one side, the rear ones may not be visible as i have not seen them
so if the abs ring are good then it wil probably be one of the wheel sensors, in this case you you may look for a garage who will hook up
the computer and pull the code for you, be carefull if the say there are no abs error codes it means the sensors are ok and most of it
there is no need to buy abs sensor for any wheel when there are no error codes
on pt cruiser you can pull engine error codes yourself without a computer, just do the key dance on the ignition,
turn key until dash lights come on then switch off and then again turn key until dash lights come on then swithch off,
then turn key for third time again until dash lights come on , you will see engine error codes displayed then says done,
if there are no error codes it will say done, howevere these are engine error codes only not abs error codes,
abs error codes are pulled using abs diagnostic tool
incase its a faulty wheel sensor, will cost £45 at dealer or £20 from scrap, then a garage can removed the tyre and plug out the old sensor cable
and replace it with a new one, one end is easy to plug in but the other end has to be pushed in at an angle,
its about 30min job and garage can charge £20 or so
my pt cruiser is back on the road with just one abs ring replaced and it all cost me £30 alltogether

Apr 11, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2000 Buick Century Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...