Question about 2002 Chevrolet Astro

1 Answer

Engine code 1345 on

I replaced the cam and cranksensor acording to the code with original chevy parts the engine light is still on and its hard to start anyone knows need help

Posted by on

  • rickems May 11, 2010

    I just replacet the rotor and cap but I dont think that I moved the distributer . Could the rotor just be a bit off ? If it was would'nt more than one cylinder be off ? Fuel injector issue ? Maybe I didnt get the plug wire on all the way ?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

Has the distributer been replaced.has it been removed.if so it could be off a tooth on the gear.Or the distributer could have a substantial amount of play back and fourth.turning the rotor.

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2.4l Why are there recurrent DTCs?


There are recurrent fault codes because the diagnosis of the cause or causes of the problem was, in part, incorrect and because many people work on the basis that........
XXXX code = replace part ABC
YYYY code = replace part DEF.

Pulling up fault codes and then replacing parts without a proper diagnosis of the cause of problems is not sound practice. The items you replaced may indeed have needed replacing but this does not mean that there are no other issues that need to be addressed.
Misdiagnosing problems, replacing functioning parts and then wondering why the warning lights and fault codes are still being generated is not uncommon practice.

Dec 05, 2015 | 2009 Pontiac G6

1 Answer

Ready smog p1345 1998 Chevy Blazer


Code 1345 means there is a problem with the alignment between the cam and crank sensors. The computer can not determine correct cam timing by the data coming from the sensors.

Aug 11, 2013 | Cars & Trucks

1 Answer

1999 GMC suburban is markin PO 1345 code.


That is a cam to crank position correlation code. I understand you can adjust it by turning the distributor until the value is right. You need a scan tool to see the value and check it each time you adjust the distributor.

Jul 18, 2012 | 1999 GMC Suburban

2 Answers

I have a 98 chevy z71 5.7 350 vortec, i have a p1345 code that stays on i clear it and as i restart the truck it comes back on, the truck runs great and has a small delay when starrted.. what can/do i need...


1345 is cam and crank sensor correlation its mainly the cam sensor going out, also the delay start that also trigger a camsensor code they call it excessive crank time check the fuel pressure that is capable of setting a cam code (1345) If fuel pressure is good (55-60 psi) expect to replace the camsensor you might as well do the crank sensor heres a nightmare on this code it can set if the distributor is off one tooth and yes these distributor have high failure rate

Jun 08, 2011 | 1998 Chevrolet K1500

1 Answer

My 03 Trailblazer ( 4200- 6cyl) started running rough a couple of weeks ago. The service engine light came on so my wife took it to the local Advance Auto store and they scanned it and the following codes...


I don't know the codes But o2 sensors are a common code thorougher.. call dealer they may give you that these codes mean ..or a manual ..its indispensable..

Apr 01, 2011 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Code 1345 pops up why


This code is an indication that the synchronization between the Crankshaft and Camshaft is off.
Can be caused by a bad crank position sensor or bad cam position sensor or worn (stretched) timing set. The MOST COMMON cause of this in chevy engines is a worn distributor drive gear.

Mar 27, 2011 | Chevrolet C3500 Cars & Trucks

1 Answer

Code 1345 came up. I already replaced wires, plugs, cam, crank sensors.


have you tried setting the cam sync.its basically setting the timing but without a timing light.you need a scan tool to do it.rev engine and hold at 1000 rpm.read the cam sync on the scan tool.should be 0 degrees.if not loosen distributor bolt and turn distributor till cam sync reads 0.also you may have a worn distributor.

Nov 25, 2010 | 1998 Chevrolet K1500

5 Answers

Trouble code 1345 crank sensor/camshaft sensor correlation


I had this same P1345 code on my 1998 GMC K1500 5.7 for about 2 years. Each time the code was erased, the "Service Engine Light" came right back on with the same code. I tried replacing the cam sensor, but that didn't solve it. I had the timing adjusted, it was out -13 degrees. After adjustment, the "Service Engine Light" went off, but only for a short time. Adjusting the timing is just a temporary mask on fixing the real problem and eventually you will run out of adjustment. I read about this same problem on another forum and someone recommended changing the distributor gear. So I checked the gear and a the teeth were worn. Replaced the gear ($35 part), readjusted the timing and the light has been off ever since. Apparently the gears in 96-99 are soft and wear enough to throw off the timing. This code is telling you the crank and distributor are out of sync. So before you start buying sensors and other misc. parts, try the distributor gear if you are getting a P1345 code.

Mar 03, 2009 | 1998 GMC Sierra

1 Answer

Location of crank sensor on renault megane 1.6, 2004


bit confused...the cranksensor will be on the gearbox housing the camsensor will be near the cams not the gearbox if the camsensor has packed up it wont start but if it packs up while driving the engine will run untill you stop it then it wont start,a cranksensor could cause the engine to stop at anytime if it fails..your problem could be the idle air control valve or a timing related issue..

Dec 31, 2008 | 2004 Renault 181

Not finding what you are looking for?
2002 Chevrolet Astro Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...