Question about Mitsubishi Galant

1 Answer

I had a radiator blow in a 93 galant and i replaced it but now the engine wont start is there some kind of trick with a sensor or something?

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    will the motor even turn over ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Look on the thermostat housing and there maybe a sensor there if there is disconnect it and it may start

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My. car v6a12 engine galant. engine crank but wont start


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Jul 26, 2012 | 1992 Mitsubishi Galant

1 Answer

Engine run won't run my engine is v6a12


can you move it by hand?what noise do you hear when trying to start.
is the gear from the starter full in the motor.are all wires connected.

Jul 26, 2012 | 1992 Mitsubishi Galant

1 Answer

Location of thermostsat on mitsubishi galant 93


Follow top radiator hose to engine and unbolt the housing this hose connects to and you will see thermostat inside.

Apr 19, 2010 | 1993 Mitsubishi Galant

1 Answer

Change the thermostat in the galant.


1. Raise the front of your Mitsubishi Galant with a jack and lower onto jack stands, or use wheel ramps. Disconnect the negative cable from the battery. Drain the coolant into a suitable container by opening the drain plug on the bottom of the radiator.
2. Step 2 Follow the upper radiator hose to where it meets the engine at the thermostat housing. Loosen the clamp at the engine end of the radiator hose and pull the hose off the thermostat housing.
3. Step 3 Remove the two bolts on the thermostat housing cover and pull off the cover. Note the position of the old thermostat and remove it from the thermostat housing. Place a rag in the thermostat housing and scrape any gasket residue from the inside of the thermostat housing cover.
4. Step 4 Take out the rag and insert the new thermostat in the same position as the old one, with the spring-side facing into the engine. Install the new gasket or o-ring, depending on the type of thermostat you are installing. Note that most late 1980s and early 1990s Galant models use a thermostat gasket.
5. Step 5 Replace the thermostat housing cover and tighten the bolts. Re-attach the radiator hose and tighten the clamp. Fill the radiator with new coolant, or use the coolant drained from your Galant earlier if it's relatively new and clean.
6. Step 6 Start your Mitsubishi Galant and run with the heater on high until it reaches operating temperature. Make sure the heater is blowing warm air to ensure the thermostat is working properly. Check for leaks and tighten the radiator hose clamps if you detect any.

Oct 25, 2009 | 2000 Mitsubishi Galant

4 Answers

ENG. RUNS HOT IN STOPPED TRAFFIC


Check your coolant temp sender, it sounds like you have a bad temp switch in front of the relay...

Sep 27, 2009 | 1993 Ford Escort 4 Door

1 Answer

Cooling Fan not coming on 2002 Mitsubishi Galant


Check the fan itself for free turning--if it grinds or is hard to turn, replace the fan motor. The engine heat sensor reports temperature to the computer which turns on the relay and it turns on the fan motor. If you have A/C, turn it on--that should force the fan on all the time the car is running. If that works, then replace the sensor. If you don't have A/C, take a chance on the sensor--it's not too expensive. Wrap the threads with several turns of teflon tape when installing and don't over-tighten.

Sep 03, 2009 | 2003 Mitsubishi Galant

1 Answer

93 Galant Sensor


it may even be the solenoid. there is one on the starter, and there may be one mounted on the side firewall

Jun 17, 2009 | 1993 Mitsubishi Galant

1 Answer

Overheating Mistu Galant


before u add water in ur radiator make sure u start ur engine and remove ur radiator cap and pour water to it when u see there is no more air in ur radiator u can close it and it will work good

Dec 27, 2008 | 2001 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...