Question about Cars & Trucks
As ive tried to get it back as original as possible after the guy i bought it off made a complete mess, iv'e noticed that the front fog lamp switch fits the connector , but the switch has 5 pins and the connector only has 4, also my trip computer is constantly flashing and will not reset, even with ignition off and keys out, it still continues to flash
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1993 Camry Check Engine Light
Therre is no DTC code "5". The DTCs start at 12. If the knock sensor (there are actually 2) was bad, you would have an acceleration issue. The knock sensor changes the timing of the spark to eliminate detonation, or "pinging". Do you have a "Ping" condition/valve rattle on acceleration?
To reset the light, open the hood, remove the 15 amp EFI fuse for 5 minutes. Replace it, and start the car and drive it until it reaches operating temperature. If the light comes back on instantly, you have a bad sensor or a bad wire.
Posted on Nov 10, 2008
Do not fit these lights yourself,you must take the vehicle to the dealer to have it done .Firstly as vehicle wasnt factory fitted you need the original homoglonation certificate from the manufacturer for the model with the foglights fitted,then you need a installation project drawn up by certifide auto engineer with the relevent technical qualifications (i have them) then they can only be fitted by a garage with an added value tax certificate,then vehicle must be presented to the local vehicle inspection depot to be mechanically inspected all over weither its due or not,the relevant paperwork plus the fee presented ,then a new vehicle registratrion document issued showing the changes.Failure to to this will cause the vehicle to fail its inspection when next presented as paperwork isnt correct ,the lights are ilrevelent as to weither they work or not,but if fitted from new they must work.Also if stopped by the guardis civil and paperwork checked,and they notice then you risk having the vehice impounded their and then on the spot ,big fine and the cost of the removal truck.
Posted on Mar 15, 2009
The door locks wont work when the car is on. Dont spend time chassing this problem beacuse it is tied in with the ignition switch.
Posted on May 16, 2009
SOURCE: renault key fob doesnt work
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:
1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working
It worked for me hope the same for you.
Please tell me if it worked and pass the message.
Posted on Sep 15, 2009
hi, this sounds like you have a bad earth at the rear lights, remove both rear light clusters and check for any signs of corrosion, give all connections a clean and a little tweek, this should cure your problem
Posted on Oct 26, 2009
Tips for a great answer:
May 17, 2013 | Volkswagen Jetta Cars & Trucks
Nov 18, 2012 | 2005 Renault Megane Scenic
Mar 30, 2017 | 1995 Dodge Ram
Aug 09, 2009 | 2000 Renault 181
Jun 17, 2009 | 2003 Renault 181
Jan 12, 2009 | 2005 Renault 181
Jun 18, 2008 | 2003 Renault 181
Dec 12, 2017 | Audi Cars & Trucks
16 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: