Question about 2007 Hyundai Tucson

Open Question

How do I change front parking light bulb in Hyundai Tucson

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
martin538
  • 117 Answers

SOURCE: Hyundai Tucson

The transmission filter is inside the transmission. You have to drain out the oil and remove the transmission pan and gasket. The filter is made of metal guaze and is screwed/bolted to the underneath of the valve body.

Posted on Apr 09, 2009

Ad
  • 67 Answers

SOURCE: change brakes on a 05 hyundai tucson

rear pad replacement is basically the same as front. 14mm bolts holding caliper and mount on hub then the piston just pushes in

Posted on Apr 09, 2009

ghost4548
  • 776 Answers

SOURCE: how do i change right headlight bulb on a 2007

You change it like you'd change any headlamp bulb. There is an access cap behind the headlamp assembly -- remove it, then remove the connector to the bulb, then remove the retaining clip/spring holding the bulb in place. Then install/insert the new bulb in the same 'ORIENTATION' as the old one. Reinstall in reverse order... ALAKAZAM!... .done!

Posted on Jun 25, 2009

  • 1986 Answers

SOURCE: headlight aiming

on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 14, 2009

  • 1 Answer

SOURCE: side light bulb change on hyundai terracan

hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust handbrake in Hyundai tucson


The adjustment is made at the handle under the console:

ADJUSTMENT OF PARKING BRAKE STROKE

1.Pull the brake lever with a force of approx. 196 N (20 kg, 44 lbs.) and check the number of clicks.

Parking brake lever stroke (Standard value) : 8 clicks

2.If the number of notches is not the standard value, adjust the cable length with the adjusting nut on the equalizer.
3.The indicator light will go out when the brake lever is fully released, and will light up with the lever pulled one notch. If it does not operate properly, replace it.
4.After the adjustment, check that the rear brakes do not drag with the parking brake lever released.

Mar 05, 2015 | 2007 Hyundai Tucson Limited

1 Answer

Hyundai tucson 2014 wont start


try putting the shifter in neutral and see if the vehicle starts up . could be the shifter linkage . hope this helps you out.

Feb 26, 2014 | Hyundai Tucson Cars & Trucks

1 Answer

2006 Hyundai Tucson brake lights


1 check you fuse if not that then check the bulbs in each light

Jun 27, 2012 | 2006 Hyundai Tucson

1 Answer

Turn Signal Bulb Change


I am guessing, the front from underneath, the back from in the trunk.

Sep 09, 2009 | 2001 Hyundai Tiburon

1 Answer

How do i change right headlight bulb on a 2007 hyundai tucson


You change it like you'd change any headlamp bulb. There is an access cap behind the headlamp assembly -- remove it, then remove the connector to the bulb, then remove the retaining clip/spring holding the bulb in place. Then install/insert the new bulb in the same 'ORIENTATION' as the old one. Reinstall in reverse order... ALAKAZAM!... .done!

Jun 24, 2009 | Hyundai Tucson Cars & Trucks

1 Answer

Fog Lamp Bulb Replacement, 05 Tucson


remove headlamp assembly and you can get it from the top pretty easy

Feb 25, 2009 | 2006 Hyundai Tucson

1 Answer

Headlight aiming


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Dec 17, 2008 | 2006 Hyundai Tucson

1 Answer

Hyundai Tucson 2.0L Year 2006


Sounds like bad CV (constant velocity) joints in the front half shafts.

They make the most noise at a full wheel cut.

Aug 06, 2008 | 2006 Hyundai Tucson

Not finding what you are looking for?
2007 Hyundai Tucson Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...