Question about 1990 Eagle Summit

Open Question

I need connection diagram of 3sped mixer grinder

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1988 buick century air mixer is staying on defrost only, is this vacuum controlled?


That would be my thought, yes.
I don't know liter size of engine? Some of the vac diagrams I looked at showed vac line for hvac and cruise.

Nov 27, 2016 | 1988 Buick Century

1 Answer

How do I remove the little lever on the seat adjuster in a 1990 mazda b2200


With a grinder... They aren't made for you to remove. And they don't sell the parts for you to replace it. You need a grinder and a little ingenuity to fix /repair them by yourself. Otherwise replace the seat.

Nov 13, 2014 | Mazda B-Series Truck Cars & Trucks

1 Answer

Do not know vacuum hose locations---need diagram.


Isn't there a vacuum diagram sticker under the hood of your car?

Jan 15, 2014 | Cars & Trucks

1 Answer

Compress calipers on rear brakes of 2008 ford fusion


Thanks for the info, but I found cheaper way. If you have a grinder, you can use the tool that comes with the hand held grinders it fits in the holes. I saved any where from $20 to $100. Don't waste your money go and buy a grinder if you don't have one, you will kill 2 birds with one stone.

Apr 14, 2012 | Cars & Trucks

1 Answer

I need a parking brake diagram for a 2007 toyota corolla. I need to replace the emergency brake cable.


unless the cable is siezed their should be no reason to change the cable ,slacken adjuster right off then remove the rear drums and clean the lip on the outside edge with a small angle grinder and adjust brakes up amnually and this will cure your problem ,then adjust handbrake cable up to 3 notches and it will be perfect

May 02, 2011 | Toyota Corolla Cars & Trucks

1 Answer

I have transplanted motor from '86 Japanese import 1300 ford laser into '86 English assembled vehicle. Because extra electronics on Japanese vertion carburetor I have not been able to connect every thing...


Have you considered making an adapter plate? You can use a piece of 1/2" aluminum plate, drill it out to match the carb venturis on one side and the manifold plenum on the other side, them blend them together. bolts going into the manifold can be used to fasten the adapter to the manifold using tulip bolts that will be flush when installed. Drill and tap your studs for the carb using the gasket for a template. of course you need to use two gaskets, one between the plate and manifold and the other for the carb. It takes a bit of work and patience. I use a die grinder when I need to make one. Kerosene is useful for keeping the grinder free of debris.

Mar 12, 2011 | 1986 Mazda 323

1 Answer

Small evap leak -- check engine need diagram in


there should be a vaccum hose diagram on the under side of the hood pertaining to the evap system, check and see. if not just google it, shouldnt be too difficult to find.

Oct 21, 2009 | 2003 Chrysler Town & Country

1 Answer

FIESTA 1800 DIESEL T REDG


easy to bypass on a diesel ,,if starter turns and its just the pump ,then to get to the valve/switch get a mini 4inch grinder and cut either side of the shroud on top of the pump so you have a piece about inch wide then cut best you can at the back bit ,wack with a decent cold chisel into the slots to remove ,underneath you will see a switch ,easy now find the 12v supply switchable from ign and connect it direct to this switch and off you go ...

Dec 31, 2008 | 1998 Ford Escort

Not finding what you are looking for?
1990 Eagle Summit Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Stewart Dibbs

Level 2 Expert

322 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...