Question about Cars & Trucks

Open Question

I have a 95 jeep Cherokee it has code 34155 I did it 2 times & got the same #. With all the reading I've been doing about the OBD codes apparently I have too many numbers. But that's what I got. What am I doing wrong. I turned it to on position then off then on then off then on & left it on & counted every flash that was after the pause redid it & came up with same thing.

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 41 Answers

SOURCE: engine code 95 jeep grand cherokee lerado

12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Posted on Dec 16, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: i have a 1988 jeep

Diagnostic Connector To read Diagnostic Trouble Codes (DTC's), the test connector for the electronic engine control system must be used. The test connector is more commonly referred to as the Data Link Connector (DLC). On all Jeep models through 1990, the DLC is a 6-pin and a 15-pin connector located under the hood on the right side of the engine compartment. On 1991–93 models, the DLC is located under the hood on the left side of the engine compartment near the powertrain control module. On 1994–98 vehicles, the DLC is located in the passenger compartment, under the driver side dashboard.

Data Link Connector (DLC) location — Jeep models through 1990

5b4e680.gif
Please don't forget to rate and let me know if this helped you.

Greg

Posted on Jul 11, 2009

rtjohnson55
  • 75 Answers

SOURCE: P0456 OBD code just appeared on a 2004 Jeep Grand

That code definition is (evaporative system small leak detected). One of the most common reasons for this code is a faulty gas cap. The evap system is strictly designed to trap fuel vapors in the tank and not allow them to scape into the atmosphere. The vehicle keeps a constant vacume on the tank and when it is unable to hold that pressure it will set the code you have. Try buying a new gas cap-thats a cheap start-clear the code and see what happens. If the light comes back on you will have to bring it to a repair shop where they will tap into the Evap system and force smoke into it. They will then observe the Evap hoses and wherever it leaks smoke will be your problem.

Posted on Dec 03, 2009

stumann2
  • 193 Answers

SOURCE: 1995 cherokee jeep Wrong code was inputted and the

Wait two hours, then put in the correct code.

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is fault code uo155


That's an OBD II code. 95 should only have 2 digit codes. If it's newer than 95, you should update the post

May 30, 2014 | 1995 Jeep Grand Cherokee

1 Answer

Cannot locate data link connector


If you're looking for the OBD 2 port for your scanner - there isn't one. OBD 2 scanners / code readers only work/are used by 1996 and newer vehicles. I also have a 95 JGC and I have to resort to the "lamp flash" method to get the trouble codes from the ECU.

Nov 07, 2012 | 1995 Jeep Grand Cherokee

1 Answer

Can codes be pulled from 95 jeep without a scanner


Yes. Turn the ignition switch to ON, do not engage the starter. Do this 3 times. On the third time leave the key in the ON position and start counting the number of times that the Check Engine Light flashes on and off. There will be a slightly longer pause when it is flashing out the next digit. Then go to http://autorepair.about.com/library/ts/obd-i/bl-dtcs-75a.htm and see what your code(s) mean.

Aug 25, 2012 | 1995 Jeep Grand Cherokee

1 Answer

1995 jeep grand cherokee larado engine code reading 34155


Hi Angela:
We cannot understand your "345155" fault code, keep in mind that 1993-1997 codes just have two digits. I suggest re-check to read and note your fault codes acdording with this read codes procedure, with out starting the engine: turn the ignition key on, off, on, off, and finally on.

The check engine light on the dash will begin to flash. The light will flash the first number of the first digit pause and flash the number of the second digit. Example: five flashes, pause, three flashes = Code 53 PCM failure or Code 54 no cam shaft position sensor signal from distributor etc, etc.

Try this and send us this fault code to send you additional detaild.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 05, 2011 | 1995 Jeep Grand Cherokee

1 Answer

What are the OBD codes for 1994 Jeep Grand Cherokee 4.0


OBD Codes can be read turn therre times ON/OFF ignition key (without start engine)... read light sequence and note... Read the Check Engine Codes

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 19, 2011 | 1994 Jeep Grand Cherokee

1 Answer

How do I get the FCC Code for my 1995 Jeep Grand Cherokee


Turn to ON position three times (dont start engine) and read odometer code blink lights; If the "check engine" light illuminates, it will either blink or remain constant, depending on the problem.

This and other additional details can find it in Check Engine and OBD Fault Codes articles.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 25, 2011 | 1995 Jeep Grand Cherokee

1 Answer

Where do u locate codes for 1994 jeep grand cherokee limited


OBD Codes can be read turn therre times ON/OFF ignition key (without start engine)... read light sequence and note... Read the Check Engine Codes

Hope this helps (remember to rate this free answer).

Oct 01, 2011 | 1994 Jeep Grand Cherokee

1 Answer

My son has a 1999 Jeep Cherokee, and it beeps 3 times and it say;s preform service could you tell us why this does this he did not get no owers manual with this Jeep


Thats just a warning telling you something on the vehicle needs service, possibly time for an oil change ,, what you need to have him do is get the OBD codes read for the vehicle,, that will tell you exactly what service is being requested , check around in your town,, there are places that will read the codes for you for free. once you get the codes, you can post them here and someone will assist you in determining what the specific code means,, or just reply to this feed and I will help you

Sep 01, 2011 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...