Question about 2003 Mitsubishi Diamante

2 Answers

2003 diamante, red lights on door???

Are they part of the security system? they dont light up when doors are locked/unlocked ...what are they for??????????

Posted by on

  • sicksickworl Feb 05, 2009

    they looked like LED's to me, it b cool if they lit up. but anyway, wats the easiest way to replace the front door speakers?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

No they are not JUST reflectors, They have a light inside them and it turns on when you open the door, and yes there is another one on the buttom of the door too, if you want to replace the bulb, you need to open the door panel 3 screws for the front door. Cheers!

Posted on Sep 02, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

They are reflectors only (traffic comming from behind you at night when door is open)

Posted on Feb 05, 2009

  • diamanteguy Feb 06, 2009

    The whole door panel needs to come off (one screw behind the door handle that opens the door one in the slot where you you hand to pull the door shut, you need to pop a plastic piece to get this

    Please rate this as fixya if it answered your intial question, and make a new question from then on (you don't get credit for answering this way)


×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 VW GOLF REAR door wont open


The rear door lock actuator has failed in the door locking unit this is a common problem you can manually unlock the door to replace the latch if you didn't have the deadlocking on if you cant try pressing the locking button twice so when the car is locked the flashing red light is not blinking ie off on the drivers. Doing this usually causes the faulty lock to release the dead locking so you can pull the inside handle to unlock the door.

Oct 13, 2016 | 2003 Volkswagen Golf

1 Answer

How to stop the blinking light on the door lock button


That is a good thing. It is a warning to would be intruders or thieves that your vehicle is armed with a security system and it is active. Move along please as this vehicle is off limits!!

Oct 18, 2014 | Cars & Trucks

1 Answer

I have a 2002 ford f150 supercrew lariat, my power door lock on all 4 doors dont work and neither switch works, theres is no clicking sound or anything, but the lights on the switch light up, also the...


You can't figure out thing's without knowing how there work , what controls them . In this case a control module .
Principles of Operation

Power Door Locks
The central security module controls the power door lock and keyless entry system. The lock and unlock operation is carried out by supplying ground to the central security module from the door lock control switch. The normal path of the actuators is to ground through the central security module. The door lock control switch will lock and unlock all doors by grounding the appropriate circuit to the central security module. The central security module then supplies power to the appropriate common actuator circuit to lock or unlock all doors.
Plus we don't guess , we test the electrical circuits with a DVOM - digital multimeter or a test light . We use a wiring diagram so we know which part of the circuits to test .

Keyless Entry
The remote transmitter sends a frequency that is received by the central security module internal antenna. Depending on the frequency received, the central security module will lock all doors or unlock the driver door. If the unlock frequency is received again within five seconds of the first unlock, the central security module will unlock all doors.
If the frequency received is for the panic button, the central security module will cycle ground to the park lamp and horn. The park lamps and horn will continue to cycle until the panic button is pressed again or the ignition switch is turned to the RUN position or 2.75 minutes elapse.
Plus we hook up a scan tool that can read codes from the control module , not a code reader for engine codes , won't work ! Need a professional scan tool .Do you know what DTC'S are ? Diagnostic trouble codes !
Central Security Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action to Take B1309 Power Door Lock Circuit Short to Ground Central Security Module Go To Pinpoint Test C . B1341 Power Door Unlock Circuit Short to Ground Central Security Module Go To Pinpoint Test C . B1485 Brake Pedal Input Circuit Short to Battery Central Security Module Go To Pinpoint Test E . B1526 Keyless Entry Circuit Short to Ground Central Security Module Go To Pinpoint Test F . B1629 PRNDL Reverse Input Short to Battery Central Security Module Go To Pinpoint Test E . B2276 Less Than Two Transmitters Programmed Central Security Module Go To Pinpoint Test I . B2425 Remote Keyless Entry Out of Synchronization Central Security Module Go To Pinpoint Test I . - All Other DTCs Central Security Module REFER to Section 419-10 .
  • All door locks are inoperative
  • Battery junction box (BJB) fuse(s):
    • 8 (15A).
    • 115 (20A) (Super Crew).
  • Circuitry.
  • Central security module.
  • Go To Pinpoint Test C .

Seams you lack the knowledge and test equipment to tackle this type of repair . Your best bet mite be to have a qualified repair shop check it out.
So, without testing i couldn't even begin to suggest what mite be wrong . I would only be guessing , as would anyone on here would.

Jul 30, 2017 | Cars & Trucks

2 Answers

What does small red light on dash at base of windshield on 2011 hyundai sonata mean?


Does the red light have a mark like the door s open r brake light or abs what r u can u post a pic of the red light I can help

Jan 27, 2013 | 2011 Hyundai Sonata 2.4

1 Answer

1993 jeep power locks dont work lights flash and security flashes. the remote will not unlock or lock the doors


Sound like a problem with the SECURITY SISTEM also called Antitheft system; try to solving applied this procedure.

The following wiring diagram and electronics circuit contains detail schematics of The 1993-1998 Jeep Grand Cherokee Laredo Anti-Theft System. Here in you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures: Alarm_Jeep_Cherokee.pdf

Good luck.

Sep 27, 2011 | 1993 Jeep Grand Cherokee

1 Answer

2003 audi a4 had dead battery, charged battery and now the key fob won't work and the security lights flash for about 5 min everytime I do anything to the car. why ?


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key batteries replaced.
How - early models
Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should operate normally after approximately 1 minute. If not, carry out programming procedure.
How - late models
If vehicle locked, manually unlock driver's door using key. Press key unlock button once. Switch ignition ON and OFF. Remove key from ignition switch. Press key lock or unlock button once. System should now operate correctly.

Apr 12, 2010 | 2003 Audi A4 Cabriolet

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

Not finding what you are looking for?
2003 Mitsubishi Diamante Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...