Question about 1997 Jeep Grand Cherokee

1 Answer

How do the volume controls work

Have no idea how the work at all and if there is a wire im just not seeing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Jeep Master
  • 1,632 Answers

Push button and turn knob left or right .

Posted on Jan 23, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On a bmw 2000 540i im only getting 2500 rpm out of motor with full throttle n a code of p1637 p0100 where do i start checking please advise me as what this relates to.

code p 0100 refers to mass air flow (MAF) sensor /volume air flow (VAF) sensor--circuit malfunction=== causes --wiring ---MAF/VAF sensor ---ECM
code p1637 refers to throttle valve position control---control deviation===causes---wiring ---
Throttle valve position control unit
take it to an accredited service shop with experience on your vehicle and discuss which would be the most likely unit to be faulty or replace the lot if you have cash to splash

Feb 22, 2017 | BMW Cars & Trucks

2 Answers

The radio plays full volume on right channel when turned on.

Anything I tell you is going to be a guess, since there has been no testing done, and we don't have the model number of the specific radio involved. However...
For a 20 year old radio, the volume and balance is almost certainly controlled by a potentiometer that has input into one leg of the fixed resistance, and the other leg (of the fixed resistance) is grounded. The movable center tap is the output to the amplifier - and its position controls the volume to that channel. If the ground leg becomes disconnected (broken wire, or a cold solder joint, or even a break in the resistor within the body of the potentiometer) then instead of "dividing" the volume, it simply provides a slight resistance inline - short answer: It goes full volume.
You can try running the control full range back and forth, and even just the old time "slap it" approach, to see if you get any static or change. If you do, that pretty well confirms the diagnosis. [If not, it just means the break is not close to touching - still almost certainly the right answer though.]
Only fix is going to be disassembly. You then may be able to find the break (and resolder it), and/or replace the volume potentiometer. Note that if you have remote volume/balance control (controls on the steering wheel), then there is some extra wiring that can likewise be involved. jk

Feb 27, 2015 | 1995 Jeep Grand Cherokee

1 Answer

We have a 3.5year c30 volvo and have recently had a problem with radio where it plays at maximum volume and we cannot control. Also notice rear parking sensors also stopped working at the same time. Any...

both accessory were installed at the same time the vol control knob grooves worn out,rear parking sensor not working may be the wire cut out visit to the accessory fitment shop

Sep 21, 2013 | 2010 Volvo C30

1 Answer

Problem with steeringwheel control devices

can be various cause 1) power amp 2) control volume 3) speaker 4) wires or ribbon cable with bad contacts or corroded.see the diagram
God bless you

Jul 17, 2013 | Cars & Trucks

2 Answers

1994 Yukon Ive changed the fuel pump and the relay, plus filter and the fuel pressure regulator and am still having problems with it starting. what the voltage should be to the pump? Im only getting 12psi...

Hi, the pump should be getting battery voltage (gray and black/white wires at the pump) thru the fusible link and the orange wire to the relay. The relay is controlled by the ECM thru the positive relay coil signal on the green/white wire.You might want to check the ground connection of the relay coil on the black/white wire. If that's good, maybe the ground wire to the pump is bad.


Aug 05, 2011 | 1994 GMC Yukon

1 Answer

I bought a 2000 ford explorer when i got it, it still had the factory stereo in it. i drove the vehicle the night i got it and it ran fine. i came home and went to put my sound system in i had to cut the...

P0743....Torque Converter Clutch Circuit Electrical
P1747 Pressure Control Solenoid A Short Circuit
P1755 Intermediate Speed Sensor (ISS) Malfunction
to be totally honest i have no idea why it doesnt run right but looking at teh codes then i would hazard a guess and you wired the radio into the automatic volume increase control ,lot of vehicles have them its where the radio will increase in volume as the speed increases and i think you have connected into this wire thinking it was switchable 12v feed from ignition for the radio ,disconnect the radio completely and try that

Feb 13, 2011 | Ford Explorer Cars & Trucks

2 Answers

I put in a cd player everythings connected but there is no sound coming out of the speakers

check your wiring, make sure its not grounded behind the dash somewhere

Sep 18, 2010 | 1993 Lexus Es 300

1 Answer

My left brake light is not working. i checked the bulb and it was bad so then i changed the bulb but still no light. i then tore apart the panels in the rear of the truck to find no power to the wiring at...

First, one wire cannot control the turn signal and brake light, as the turn signal and brake light have to work independently of each other so I would verify the color code for the brake light wire and then check it.

Jul 14, 2009 | 1993 Chevrolet S-10 Blazer

3 Answers

Radio shows working but no sound

Radio and on star does not work what should i do??

Mar 07, 2009 | 2004 Chevrolet Impala

1 Answer

Lights not working

im guessing its a blown fuse in the fuse box...check the fuses and see if any are blown..if that doesnt work there could be a short or a bad wire in the dash...but im not sure im not real good with nissans. good luck!

Nov 16, 2008 | 2005 Nissan Murano

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides