Question about Cars & Trucks

1 Answer

I just replaced the actuator. What else could be the problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Cars & Trucks Master
  • 1,632 Answers

The Fuel Pressure sensor . And TCP .

Posted on Jan 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

2 Answers

I have codes b0428 and B3532 coming up . I just need to know what the problem may possibly be and what might I do to fix it ?


Code B0428 is for the rear temp actuator.
Code B3532 is for the rear mode actuator for the HVAC unit

May 19, 2016 | 2006 Chevrolet Chevrolet Uplander

2 Answers

It has duel climate controls. With both set to 60, driver's side blows hot while passenger's side blows cool. What does it sound like


our honda crv did this , there was a problem with the heater core being partially pluged...there ended up being a recall on heater core

Apr 30, 2016 | 2006 Chevrolet Trailblazer

1 Answer

Blend door on 2003 montr carlo


How To Install Replace AC Heater Temperature Actuator ...

? 4:40
https://www.youtube.com/watch?v=mVP09M7hLB4
Jul 21, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/temperature-blend-door-actuator/i/ ... To Install Replace AC Heater Temperature Actuator 2000-05 ChevyMonte Carlo.

2006 Monte Carlo: Blend Door Actuator Replacement ...

? 2:19
https://www.youtube.com/watch?v=_B17o-Ljhfs
Mar 31, 2015 - Uploaded by Adam Strojny
In this video I will show you guys how to replace the actuators behind the glove compartment that where causing ...

Chevy Blend Door Actuator Replacement - Part 3 - YouTube

? 12:26
https://www.youtube.com/watch?v=1q9ugwlqDoo
May 14, 2013 - Uploaded by Dan Abbott
My final step to replacing the blend door actuator. ... Thanks for the video, need to do this on my 04 monte carlo ss, went to use the heat today .... 2003 Chevy Suburban AC-heater air direction problem.mov - Duration: 1:36. by ...


Dec 26, 2015 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

2005 GMC YUKON REAR HATCH ACTUATOR BUZZING


Check the ground to the actuator, if that is ok replace the actuator.

Aug 28, 2012 | 2005 GMC Yukon

1 Answer

2002 trailblazer has four loud clicking noise when i start it sounds like it is be hind 4wd selector switch?


#04-01-38-002A: Clicking Noise From Instrument Panel After Vehicle is Started (Replace Mode Valve Actuator Assembly Using Special Tool GE-47676) - SUPERSEDED BY BULLETIN 05-01-38-001A - (Oct 21, 2005) Mode Valve Actuator Replacement Tools RequiredGE-47676 Mode Actuator Removal Tool
Removal Procedure
  1. Remove the left floor duct. Refer to Floor Air Outlet Duct Replacement - Left Side .
  2. Important: The service actuator is positioned in the bi-level mode. Place the mode door in the middle of the door's travel.
  3. Disconnect the mode actuator electrical connector.
  4. Remove the mode actuator mounting screws.
  5. Using GE-47676 remove the mode actuator.
Installation Procedure
  1. Install the mode actuator.
  2. Notice: Refer to Fastener Notice in the Preface section.
  3. Install the mode actuator mounting screws.
  4. Tighten
    Tighten the screws to 1.9 N·m (17 lb in).
  5. Connect the mode actuator electrical connector.
  6. Install the left floor duct. Refer to Floor Air Outlet Duct Replacement - Left Side .

Jul 29, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Drivers side blend door actuator not working properly. replaced actuator, when plugged in before installing actuator runs constantly. Is the problem in the control board or in the dash?


Hello: I have bad news for you, if you run the actuator without it connected to the door the actuator is ruined, it will have to be replaced. After replacement the system has to have the doors (actuators re-calibrated.) re-calibrated. This is done with a Tech 2, A GM special tool.

Nov 12, 2010 | 2005 Chevrolet Impala

1 Answer

How to install ac mode actuator on 2003 gmc sierra


prev.gif next.gif Air Door Actuators Removal & Installation Air Temperature Actuator Air Temperature Actuator Replacement gm-10-00-559.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel hush panel.
  2. Disconnect the connector from the air temperature actuator.
  3. Remove the air temperature actuator mounting screws.
  4. Remove the actuator from the HVAC assembly.
To Install:
  1. Position the air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Install the electrical connect to the air temperature actuator.
  4. Install the instrument panel hush panel.
Right Side Air Temperature Actuator (2003-2007) Right Air Temperature Actuator Replacement gm-10-00-560.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel carrier.
  2. Disconnect the connector from the right air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the right air temperature actuator.
To Install:
  1. Position the right air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P carrier.
  5. Calibrate the actuator.
Left Side Air Temperature Actuator (2003-2007) Left Air Temperature Actuator Replacement gm-10-00-561.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the I/P insulator panel.
  2. Disconnect the connector from the left air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the left air temperature actuator.
To Install:
  1. Position the left air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P insulator panel.
  5. Calibrate the actuator.
Mode Actuator Mode Actuator Replacement gm-10-00-562.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the floor air outlet from the floor duct.
  2. Remove the center console and center console duct (if equipped).
  3. Disconnect the electrical connection at the mode actuator.
  4. Remove the mode actuator mounting screws from the HVAC module.
  5. Remove the mode actuator with the actuator cam attached.
To Install:
  1. Position the mode actuator with the actuator cam to the HVAC module.
    • Align the heater/defroster valve lever with the cam slot
    • Align the A/C valve lever with the cam
  2. Install the mode actuator mounting screws.
  3. Connect the mode actuator electrical connection.
  4. Install the center console duct and the center console (if equipped).
  5. Install the floor air outlet duct extension to the floor air duct.
  6. Calibrate the actuator.
Air Inlet Actuator/Recirculation Actuator Delphi Recirculation Actuator Replacement (Delphi) gm-10-00-564.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel upper trim panel.
  2. Remove the instrument panel lower trim panel and glove box assembly.
  3. Remove the passenger side air bag.
  4. Disconnect the connector from the recirculation actuator.
  5. Remove the recirculation actuator mounting screws.
  6. Remove the recirculation actuator from the HVAC assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Connect the electrical connector to the recirculation actuator.
  4. Install the passenger side air bag.
  5. Install the instrument panel lower trim panel and the glove box assembly.
  6. Install the instrument panel upper trim panel.
  7. Calibrate the actuator.
Visteon Recirculation Actuator Replacement (Visteon) gm-10-00-566.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the HVAC module assembly.
  2. Remove the evaporator core cover from the HVAC module.
  3. Remove the recirculation actuator from the HVAC module assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Install the evaporator core cover to the HVAC module.
  4. Install the HVAC module assembly.
  5. Calibrate the actuator.
prev.gif next.gif

Jul 09, 2010 | 2000 GMC New Sierra 1500

1 Answer

Replace 2004 Hundai Sonata Door Lock Actuator?


take all screws of ,,then take screws of actuator and cables then remove it ,,put in new one put everything back together

Nov 27, 2009 | Hyundai Motor 2004 Sonata

1 Answer

How to replace 2000 buick century temperature actuator


First, what is the problem that you need to replace the actuator? Is the air flow from the vents not changing? If this is the problem, the actuator is inside the venting behind the control panel and is difficult to get to but is possible. Follow the hoses on back of temp controls to the actuator. There should be 2 small bolt screws to remove to change out actuator.
If this is for something else, let me know

Jul 01, 2009 | 2000 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...