Question about Cars & Trucks

1 Answer

Parts for gazelle edge

Need bushings and retaining screws for cables

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Cars & Trucks Master
  • 1,632 Answers

Rock Auto has some on sale .

Posted on Jan 23, 2013

  • THANKS FOR THE HELP, BUT SOME HOW MY QUESTION WAS ROUTED TO THE WRONG AREA. GAZZELLE I WAS REFERING TO IS AN EXERCISE MACHINE ORIGINALLY SOLD ON TV!!!!

×


2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dgjtex
  • 405 Answers

SOURCE: 1985 Volvo 240 Speedometer cable retaining screw broke

I'd be hitting the wrecking yard, most will give you those parts if you remove them.

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the door panel of the 2007 sebring


most door panels have plastic push in fasteners around the edge about . there is a special tool to help get them out but often they break on removal however cheap to buy and replace. Use a couple of flat tip screwdrivers to quickly pop the panel away from the door frame all around the edge. get as close to the fastener(tightest spots)with your tool for best effect

Dec 11, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

How do I replace an instrument cluster bulb


it's a piece of cake.All you do is unsnap the radio/a/c bezel remove the screw's from the bottom of the cluster bezel and the cluster bezel will unsnap off the cluster and there is like 4 screws holding the cluster in.Then the bulbs just twist in and out. TRIM PLATE BEZEL REPLACEMENT - INSTRUMENT PANEL (I/P) CLUSTER REMOVAL PROCEDURE 1. Pull out on the accessory trim plate in order to release the retaining fasteners. 2. Disconnect the accessory trim plate electrical connector(s). 3. Remove the screw retaining the cluster trim plate to the center trim panel. 4. Lift up on the cluster trim plate to release the retaining fasteners. 5. Remove the cluster trim plate. INSTALLATION PROCEDURE 1. Align the retaining fasteners with the center trim panel. 2. Push on the outer edge of the cluster trim plate in order to secure the retaining fasteners. 3. Install the screw retaining the cluster trim plate to the center trim panel. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the cluster trim plate screw to 2.5 N.m (22 lb in) . 4. Connect the accessory trim plate electrical connector(s). 5. Align the retaining fasteners with the I/P. 6. Push on the outer edge of the accessory trim plate in order to secure the retaining fasteners.tedww_1.jpgtedww_0.jpgtedww.jpg

Mar 08, 2011 | 2006 Saturn ION

1 Answer

How to replace main heater fan


Blower Motor REMOVAL & INSTALLATION Front Fig. 1: Front heater blower motor assembly 89696g02.gif
Remove the glove box to access the front blower motor, which is on the firewall 89696p02.jpg
The blower motor is retained by four bolts (arrows) 89696p03.jpg
The blower motor vent tube helps to cool the blower motor for efficient operation 89696p04.jpg
Push up on the clip to remove the blower motor connector 89696p05.jpg
A ratchet with extensions makes removal of the retaining screws easier 89696p06.jpg
Lift the blower motor over the control cable . . . 89696p07.jpg
. . . and remove it from the vehicle 89696p08.jpg
  1. Disconnect the negative battery cable.
  2. Open the glove box door. Gently squeeze the retainers at the rear of the box inward and allow the box to swing downward. NOTE: If additional access is required, unfasten the glove box hinge retainers and remove the assembly.
  3. Label and disconnect the electrical harness from the blower motor.
  4. Remove the blower motor housing tube and/or blower motor cover.
  5. Remove the blower motor retaining screws.
  6. Remove the blower motor from the A/C evaporator. To install:
  7. Install the blower motor in the A/C evaporator and tighten the retaining screws securely.
  8. Install the blower motor housing tube and/or blower motor cover.
  9. Connect the electrical harness to the blower motor.
  10. Reinstall the glove box and close its door.
  11. Connect the negative battery cable.
Rear Fig. 2: Service cover push pin locations 89696g03.gif
  1. Disconnect the negative battery cable.
  2. Remove both rear passenger seats.
  3. Remove the three push pin retainers from the lower edge of the auxiliary heater and air conditioning service cover.
  4. Lift the service cover outward and upward to remove.
  5. Label and disconnect the electrical harness.
  6. Remove the blower motor housing tube.
  7. Loosen the three retaining screws and remove the blower motor. To install:
  8. Install the blower motor and tighten retaining screws securely.
  9. Install the blower motor housing tube.
  10. Connect the electrical harness.
  11. Position the service cover and install the three push pin retainers from the lower edge of the cover.
  12. Install both rear passenger seats.
  13. Connect the negative battery cable.
prev.gif next.gif

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

My driver side electric window assembly collapsed and the window fell down inside the door. The motor is still very good, but I need info and/or a diagram of how it is assembled in order to repair it and...


f82a631.gif
  1. Lower the window halfway.
  2. Remove the front side door trim panel.
  3. Remove the water deflector.
  4. Support the window in a position needed to access the window rivets by inserting a rubber wedge door stops (1) at the front and rear of the window between the window and the door inner panel.
  5. Drill out the window rivets (3) with a 1/4 inch drill bit.
  6. Remove the window (1) by lifting out of the door. Important: Inspect the window bushings, window bushing retainers, window front up stop, window stabilizer pins and window wedges on the window for damage.
  7. Remove the window bushings and window bushing retainers if necessary, using a flat-bladed tool covered with cloth body tape.
  8. Remove the window front up-stop screw if necessary.
  9. Remove the window front up-stop, front up-stop nut and front up-stop washer if necessary.
  10. Remove the window stabilizer screws, if necessary.
  11. Remove the window stabilizer pins, stabilizer pin nuts and window wedges if necessary.
Installation

  1. Install the window stabilizer pins, stabilizer pin nuts and window wedges if necessary. Notice: Refer to Fastener Notice in Service Precautions.
  2. Install window stabilizer screws, if necessary. Tighten the window stabilizer screws to 7 N.m (62 lb in).
  3. Install the window stabilizer pin nuts, if removed. Tighten the window stabilizer pin nuts to 8 N.m (71 lb in).
  4. Install the window front up-stop washer, if removed.
  5. Install the window front up-stop screw, if removed. Tighten the window front up-stop screw to 7 N.m (62 lb in).
  6. Install the window front up-stop nut if removed. Tighten the window front up-stop nut to 8 N.m (71 lb in).
  7. Install the window bushings and bushing retainers, if removed.
  8. Install the window (1) into door so that holes in window bushings line up with holes in channel.
  9. Install the window rivets (3) in sequence.
  10. Install the water deflector.
Hope this helps

Oct 15, 2010 | 2002 Chevrolet Camaro

1 Answer

Window motor and regulator replacement


Door Glass REMOVAL & INSTALLATION
  1. Remove the door trim panel and the inner panel water deflector.
  2. Raise or lower the window, as applicable, to the half-up position. CAUTION
    Make sure to properly support the window. If the window drops into the door personal injury or window damage may result.
  3. Support the window in the position needed to access the rivets by inserting rubber wedge door stops at the front and rear of the window between the window and inner door panel. Fig. 1: Support the window with rubber wedges in the door channel 88140g46.gif

  4. Use a 1⁄4 in. (6mm) bit to drill out the attaching rivets on the sash channel. Fig. 2: Location of the window retaining rivets 88140g47.gif

  5. Carefully raise the glass to remove from the sash channel, then remove the glass from the door.
  6. Inspect the bushings, retainers, up stop, pins and wedges on the window for damage.
  7. If necessary, remove the bushings and retainers using a prytool covered with cloth body tape.
  8. If necessary, remove the following:
    1. Window front up stop bolt/screw.
    2. Up stop, nut and washer.
    3. Window stabilizer bolts/screws.
    4. Stabilizer pins, nuts and wedges. Fig. 3: Exploded view of the window glass and related components 88140g48.gif
      To install:
  9. If removed, install the window wedges and stabilizer pins.
  10. If removed, install the stabilizer pin bolts/screws and tighten to 62 inch lbs. (7 Nm).
  11. Install the stabilizer pin nut, if removed and tighten to 71 inch lbs. (8 Nm).
  12. If removed, install the up stop and washer.
  13. If removed, install the up stop bolt/screw and nut. Tighten the bolt/screw to 62 inch lbs. (7 Nm) and the nut to 71 inch lbs. (8 Nm).
  14. If removed, install the bushings and retainers.
  15. Carefully position the window into the door so the holes in the bushings lines up with the holes in the channel.
  16. Install the rivets in sequence.
  17. If necessary, adjust the window as outlined later in this section.
  18. Install the water deflector and trim panel.
  19. Remove the drilled out rivets and shavings from the door.
  20. Check the rivet bushings and retainers on the glass for damage. If necessary, remove the bushings using a flat-bladed tool covered with a cloth body tape. Install by snapping the rivet retainer into the bushing.
  21. Lower the glass into the door and position on the sash channel so the holes in the sash line up with the holes in the bushings and retainers.
  22. Using rivet tool J–29022 or equivalent, install 1⁄4 in. (6mm) peel type rivet (part No. 20184399 or equivalent) to retain the glass to sash channel.
  23. Install the rear guide channel.
  24. Install the front up stop to support on the inner panel.
  25. Before installing the trim parts, check the window operation for performance and fit to roof rail weatherstrip.
  26. Install the inner panel water deflector and the door trim panel.
prev.gif next.gif

Jul 08, 2010 | 1997 Chevrolet Camaro

1 Answer

How to replace the headlight on a 1987 chevy el camino


Check this GM Chevy Mid-Size Cars 1964-1988 procedure from Repair Guide...


Headlights - REMOVAL & INSTALLATION
If some or all of the headlight bulbs being replaced still operate, refer to the headlight aiming procedure later in this section to ease checking or adjustment of the headlights after installation.
  1. Disconnect the negative battery cable.
  2. Loosen and remove the retaining screws, then remove the headlight bezel from the front of the vehicle.
  3. On most models, the headlight bulb retaining ring is only held on by retaining screws. If so, remove the bulb retaining ring screws. These are the screws which hold the thin metal ring which holds the bulb against the adjusting plate. Do not touch the two headlight aiming screws, at the center of the top and side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.

One way to identify the retaining ring screws is that they will be threaded through a lip on the outer edge of the retaining ring before threading through the adjusting plate. One the other hand, the adjustment screws are threaded through the adjustment plate and a spring loaded holder underneath it.

23f036c.jpg

Fig. 1: Exploded view of a common dual headlight mounting assembly-1983 Malibu shown typical
  1. Some later model vehicles will use a spring on the retaining ring. If so equipped, disengage the spring from the retaining ring, using a cotter pin removal tool, then remove the retaining ring screws.
  2. Pull the bulb and ring forward and then separate them. Unplug the electrical connector from the rear of the bulb and remove the bulb from the vehicle.
To install:
  1. Plug the new bulb into the electrical connector.
  2. Position the retaining ring over the bulb, then install the assembly to the adjusting plate. Secure using the retaining screws and, if applicable, the spring.
  3. Install and secure the headlight bezel.
  4. Connect the negative battery cable.
f270907.jpg

Loosen and remove the headlight bezel retaining screws

55278f9.jpg

Make sure all of the screws are removed, then pull the bezel from the front of the vehicle

b98b91d.jpg

Loosen and remove the retaining ring screws

b83d4c4.jpg

Pull the retaining ring and bulb forward to separate them


5713f83.jpg

Unplug the electrical connector from the rear of the headlight


Hope helps (remember rated this).

Jul 01, 2010 | 1987 Chevrolet El Camino

2 Answers

My antena wont go down ,and the motor wont go off , even when the car is shut off .


Unplug the harness to the ant.It will not go off,until you replace the whole ant.mass.The gear(plastic)are stripped out,and the motor can not sense that the any.is moving.

Jan 19, 2010 | 1991 Oldsmobile Eighty Eight

2 Answers

How do you remove the front bumper cover on a 98 honda accord sedan EX


Apply the parking brake and raise the vehicle and support it securely on jackstands.

Disconnect the negative battery cable, then the positive battery cable and wait two minutes before proceeding further (make sure you have the code if you have an anti-theft radio because you will need it after disconnecting the battery).

Working under the vehicle, detach the screws securing the lower edges of the bumper cover (use a small screwdriver to pop the center button up on the plastic fasteners, but do not try to remove the center buttons. They stay in the ferrules)

Remove the bolts, screws and plastic pins on each side retaining the bumper cover to the splash shields. Remove the bolt on each side where the bumper cover attaches to the fender.

Working at the top, detach the retaining bolts (2) securing the bumper cover to the hood latch support. Remove the cover.

When you put it back, make sure the tabs along the top edge of the bumper cover fit into the corresponding clips on the body before attaching the bolts and screws. An assistant is helpful.

Hope this helps you.

Jan 05, 2010 | 1998 Honda Accord

1 Answer

How do I remove the door panel and replace the inside door handle


PLEASE DON'T FORGET TO RATE!!

Door Panel
  1. Remove the door handles and the locking knob from the inside of the doors.
If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.
  1. If equipped with remote control mirrors, remove the remote mirror escutcheon, then disengage the end of the mirror control cable from the escutcheon.
5670a53.gif
Door lock remote control handle

849dcc4.gif
Removing the clip from inside the door handle

3. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switches and the cigar lighter (if equipped) from the electrical harness.
4. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.

7c4bfcc.gif
View of the armrest switch cover plate and remove mirror cable attachment

  1. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.
  1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
If equipped with courtesy lights, disconnect the wiring harness.
  1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.
  1. If removed, glue a new inner pad to the door inner panel.
If equipped with courtesy lights, connect the wiring harness.

e8e7539.gif
Exploded view of the window regulator handle

4df80bc.gif
Exploded view of the door trim panel

  1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.
  1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
  2. If equipped with an integral armrest, install the retaining screws.
  3. If equipped with a switch cover plate in the door armrest, engage the switches and cigar lighter (if equipped) harness connectors, then install the cover plate and secure using the plate screws.
  4. If equipped with remote control mirrors, engage the control cable, then install the remote mirror escutcheon.
If equipped, install the pull handle screws through the handle into the door inner panel.
  1. Install the door handles and the locking knob to the inside of the doors.
3e5ae04.gif
Exploded view of the 2-piece door trim

  1. Remove the door handles and the locking knob from the inside of the doors.
If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.
  1. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switch
from the electrical harness.
  1. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.
  2. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.
  1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
If equipped with courtesy lights, disconnect the wiring harness.
  1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.
  1. If removed, glue a new inner pad to the door inner panel.
If equipped with courtesy lights, connect the wiring harness.
  1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.
  1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
  2. If equipped with an integral armrest, install the retaining screws.
  3. If equipped with a switch cover plate in the door armrest, engage the switch harness connector, then install the cover plate and secure using the plate screws.
If equipped, install the pull handle screws through the handle into the door inner panel.
  1. Install the door handles and the locking knob to the inside of the doors.

Nov 16, 2009 | 1987 Chevrolet Monte Carlo

1 Answer

1985 Volvo 240 Speedometer cable retaining screw broke


I'd be hitting the wrecking yard, most will give you those parts if you remove them.

Dec 27, 2008 | 1985 Volvo GLT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...