Question about 2002 Ford SVT Focus

Open Question

I need a diagram for 2002 ford focus timing belt replacement

Please post a picture of the diagram of the time setting for replacing the timing belt

Posted by on

  • bayegirl Jan 31, 2009

    I need a 2002 Ford Focus timing belt diagram. Does anyone know where to find one online?

×

6 Suggested Answers

  • 184 Answers

SOURCE: timing mark-specs

ADVISE YOU NOT TO TOUCH THIS UNLESS UR MECHANILLY COMPENENT YOU NEED SPECIAL TIMING PINS & BAR FOR THIS & ARE NOT THE EASIEST TO TIME UP.

Posted on Jan 14, 2009

BCAS1298
  • 3092 Answers

SOURCE: setting timing belt 2.0 split port focus engine

Hope this helps.

39fe2de.gif

Posted on Jul 19, 2010

  • 337 Answers

SOURCE: 2002 ford focus timeing belt set up

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801ecf24

Posted on Dec 07, 2008

  • 21 Answers

SOURCE: Focus timing belt replacement.

This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Posted on Aug 31, 2009

  • 122 Answers

SOURCE: diagram for timming belt on 2002 ford focus 2.0ltr

there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Posted on May 28, 2010

Testimonial: "thank you"

saailer
  • 1868 Answers

SOURCE: timeing belt broke in a

Hello! See diagram below...I do not have the ability to send the entire procedure to you due to its length...I've included a diagram of the assembled belt, cam timing and crank setting...You have the option of sending an e-mail and I'll send you the entire procedure...That is entirely up to you...

Guru.......... Saailer@ec.rr.com





saailer_95.gif









saailer_98.gif


CAM TIMING



saailer_99.gif

CRANK SETTING

Posted on Aug 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace broken timingbelt


What engine does yours have ? 2.0l Zetec ? You need special tools !

May 31, 2015 | 2000 Ford Focus

1 Answer

Is there a ford focus timing marks single overhead cam diagram


depending on trans and engine mount type the mark my be on flywheel but generally most cars it is located on the belt pulley attached to crank rod, center bottom one on engine block. the timeing mark should be visable from top looking down. if you use a big ratchet to turn over the engine by hand and go slowly, you should see thhe marks pass as you do so.

Aug 14, 2014 | 2002 Ford SVT Focus

1 Answer

Timeing belt broke in a 2002 ford focus. How do you set the timeing back?


Hello! See diagram below...I do not have the ability to send the entire procedure to you due to its length...I've included a diagram of the assembled belt, cam timing and crank setting...You have the option of sending an e-mail and I'll send you the entire procedure...That is entirely up to you...

Guru.......... Saailer@ec.rr.com





saailer_95.gif









saailer_98.gif


CAM TIMING



saailer_99.gif

CRANK SETTING

Aug 24, 2011 | Ford Focus Cars & Trucks

1 Answer

Please Help! Need the diagram for replacing serpintine belt on a 2002 ford focus zx3 2.0L 14 SFI - thank you!


http://www.focusfanatics.com/forum/showthread.php?t=43557

there you go, if you need another diagram for one without AC its in that same page, remember to use belt dressing, go slowly, and if you need one, use a belt tensioner wrench to help you slide it off, a special trick is to put the belt on the water pump pulley last, as the rounded edge is easier to slide on to, as well as making sure the belt length is correct

Mar 01, 2011 | 2002 Ford SVT Focus

2 Answers

I need the fan belt diagram for ford focus 1800 tdi 2002 model so I can replace the belt


moz-screenshot.pnge105f1e.jpg

This is for model 2002-2005. You need to specify the model type.

Jun 28, 2010 | 2002 Ford SVT Focus

2 Answers

Diagram for timming belt on 2002 ford focus 2.0ltr


there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Jan 23, 2010 | 2002 Ford SVT Focus

2 Answers

I need a diagram of the serpentine for a ford focus 2002 z3


Hi

Thanks for using FixYa. You can look at this picture for serpentine belt for your 2002 Ford Focus Z3--

3103caa.jpg

Ford Focus Z3 Serpentine belt Removal--

· Jack up the front of the vehicle and support it on jack stands. Use a wrench to remove two bolts and take off the drive belt lower cover.
· Note belt routing and make a sketch for your reference if you don't have a belt routing diagram from the manufacturer.
· Find the belt tensioner pulley. Use your wrench to rotate the tensioner pulley by pulling clockwise on a bolt in the center of the pulley. Slip the old belt off of the tensioner pulley.
· Release the belt tensioner. Slip the belt off of the pulleys and install the new belt according to your routing diagram.
· Rotate the tensioner again to allow the new belt to slip over the tensioner pulley. Release the tensioner again. Replace the drive belt lower cover and lower the vehicle.

Please do rate the solution and revert for further assistance.

Thanks
Rylee

Sep 06, 2009 | 2000 Ford Focus

1 Answer

Timing mark-specs


ADVISE YOU NOT TO TOUCH THIS UNLESS UR MECHANILLY COMPENENT YOU NEED SPECIAL TIMING PINS & BAR FOR THIS & ARE NOT THE EASIEST TO TIME UP.

Jan 09, 2009 | 2002 Ford SVT Focus

Not finding what you are looking for?
2002 Ford SVT Focus Logo

Related Topics:

1,033 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...