Question about Jeep Liberty

1 Answer

Where is my plug in for block heater 2010 jeep liberty

Posted by Anonymous on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

It is on the right front (facing the engine compartment) side of the engine compartment. It is a three pronged plug that has a plastic cover over it so you can not see the bare prrongs of the plug. It will be wire tied up somewhere around the dip stick area if it has never been used. there is enough wire to thread it to the front grille area for easy access.

Posted on Jan 24, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: block heater not working jeep liberty crd 2006

Coming from an area where block heaters are pretty much unnecessary, I have seen lots of them but never worked on any. The ones I've seen were just a small version of the heater element in a home water heater. To check them, Just put an ohm meter across the plug. If the circut is open, the element has failed.Cost of replacing OEM depends upon the unit price and shop labor charges per hour.
There are aftermarket heaters available from many different sources, some of which are attached externally, which you may be able to do yourself. I now live in an area which is very cold (-10 today) but, I use a good synthetic oil in my engine, keep my battery fully charged and have never had a starting problem yet!!!
good luck with yours!!!

Posted on Jan 16, 2009

  • 150 Answers

SOURCE: 2003 Jeep Liberty heater fan problem

It is the blower motor resistor. Look under the passanger side dash and locate the fan housing (looks round and black in color. Then locate the resistor it will be in that housing usually withtwo ten millimeter nuts or two simple screws holding it in. unplug the harness to the resistor and remove the resistor. Part store price is approx. 50.00. Note: on aftermarket (not Jeep) resistor sometimes you have to modify the housing a little to get it in. Hope this helps.

Posted on Feb 01, 2009

  • 74 Answers

SOURCE: heater on2002 Jeep liberty wont stay warm unless its moving

Check to see if the coolant level is low.

Posted on Dec 13, 2009

  • 173 Answers

SOURCE: Brand new 2010 Jeep Liberty throwing error codes ??

Hello... This doesn't sound good... I would not recommend driving it. Also, I don't think you have a lemon it sounds like the error codes are indicating a reprogramming that needed to be done. After that, the vehicle should be as good as new... Hey it is new (smile)

Good Luck...

Posted on Dec 25, 2009

  • 6468 Answers

SOURCE: 2010 jeep liberty uses 1 quart of oil every 1000 miles

i should be under factory warr and they should fix it for free

Posted on Apr 21, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Changed water pump and thermostat in 2010 jeep liberty still no heat

You didn't get all the air purged out of it. To new to be a clogged heater core. Unless some one has dumped a bunch of radiator stop leak in it.

Mar 28, 2015 | 2010 Jeep Liberty

1 Answer

Need cooling system diagram for 2010 jeep liberty 3.7 v6

It is electric.It is mounted in the center on top off the air plenum. You have to remove the dash to get to it. Last one I did was the heater core. 2003, had to remove the dash out of the vehicle, drop the steering column and remove the air plenum. All day job. You need a manual, lots of nuts, bolts, and screws to remove.

Dec 28, 2014 | 2010 Jeep Liberty

2 Answers

Why is my 2010 Jeep Liberty only blowing cold air?

Element in heater blown , could be independent fuse for heat also , check fusebox

Dec 01, 2014 | 2010 Jeep Liberty

1 Answer

Why does my 2010 Jeep Liberty just blows cold air?

Blend door is not moving to open to the heater core. Coud be that the cable is not connected to the dash lever but if it's vacuum actuated the vacuum line could be off. Check that your getting vacuum.

Dec 01, 2014 | 2010 Jeep Liberty

1 Answer

Are there one or two fuse boxes in a 2010 jeep liberty ?

Two. One under the dash and one under the hood on the driver side.

Aug 07, 2014 | 2010 Jeep Liberty

1 Answer

2010 jeep liberty heater blower not working

There are 3 reasons a heater blower will not run. I will list them in most common cause order.
1. No power to the motor.
Check the fuse (it is listed in your owners manual).
Check for power at the motor.
If the fuse is good and there's no power at the motor then it gets complicated and you should take it to someone with experience in fixing these.

2. Motor is bad
Remove the motor and apply power (12 volts) to it. If it is good it is going to spin fast, so better hold on tight. These things can hurt when they are loose and turned on.

3. Something is blocking the fan.
Remove the motor and look for the pencil (or whatever) may be stopping the fan from turning.

If what I've written doesn't make sense, then I would suggest either take it to someone who has experience or buy a repair manual (and other tools) and plan to spend some time reading and experimenting.

Jun 26, 2014 | 2010 Jeep Liberty

1 Answer

Block heater

It should not make much difference as long as the heater makes contact with the coolant. Some may be more accessable than others.

Jan 23, 2014 | Cars & Trucks

1 Answer

Where is the plug in to keep jeep warm in the winter when its cil

You may not have a block heater on your vehicle. It depends where you originally bought your vehicle. In colder climates like Canada a block heater is a requirement.

Nov 22, 2008 | 2002 Jeep Liberty

1 Answer

Block heater

go buy a zero start frostplug engine heater you will also need a hammer and a long punch to force out the old soft plug. in the kit it will tell you what frost plug to remove. and in what position the heater will need to be installed .

Aug 23, 2008 | 2004 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides