Question about 2008 Toyota Camry

1 Answer

2008 FJ six speed manual high idle between gears

I have a 2008 FJ with manual six speed. Toyota says there is a device on my engine that manages the rpm while shifting. When shifting, and letting off the throttle this device will keep the rpm's above 2100 ... even until I roll to a stop if the clutch is depressed. Toyota also says if this device is disabled the check engine light comes on. Does anyone know a way around this?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

TRY CHANGING THE ECU FOR A NEW ONE SOUND LIKE YOU GOT THE WRONG ONE ON

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the problem of toyota avanza 2008 model k3 engine very high rpm 1700 to 2000rpm


Double check work, there is a bad connection, could even be a bad "new" part. It wasn't doing this before, was it?
so something you did is causing this. High speed seems to me the Throttle position sensor is not adjusted properly. Its calling for more fuel. or The throttle is stuck somehow, not closing at idle. or installed bad?

Mar 15, 2015 | Toyota Cars & Trucks

1 Answer

Coaster idling high and high fuel consumption


Water temperature is low cost oil is certainly the easiest way is with a hard shell to block part of the warming effect of the radiator well as for how much you want to try to stop. Idle temperatures will rise up relatively low. What is the pull speed? Not run fast but continues to run uninterrupted some time. Usually two hours can be. Is to allow the engine to reach full swell purpose. Such a shift is to be based on the vehicle speed and the reference engine speed. Not based on the engine speed. Driving is probably the single 30 towards third gear, fourth gear towards forty, fifty five-speed ahead. Many people on the car ahead of change. As long as the engine sounds smooth, no trailer can be.

Dec 11, 2013 | Toyota Cars & Trucks

1 Answer

2008 Corolla that has a rattle noise in the engine compartment


I would check exhaust system for loose heat shields or bracket.

Jul 02, 2012 | 2008 Toyota Corolla

2 Answers

Recommended oil for fj crusier 2008


Check the owner's manual or call the local dealership.

Feb 26, 2011 | 2008 Toyota FJ Cruiser

1 Answer

Idling problem toyota altis


Either there is a vacuum leak causing the high idle, or
the IACV is bad or being controlled by the computer to make idle speed too high:

To change the IACV refer to the following:
Idle Speed Control (Idle Air Control) Valve Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the throttle body. Idle speed control valve toy_cor-04-18-1187.gif

  3. Remove the 3 mounting screws from the throttle body. Remove the idle speed control valve and gasket.
To Install:
  1. Using a new gasket install the idle speed control valve on the throttle body with the 3 mounting screws.
    • Tighten 33 inch lbs. (3.7 Nm).
  2. Install the throttle body.
prev.gif next.gif

Jul 16, 2010 | 2004 Toyota Corolla

1 Answer

High Idle, Slow fueling


superise the car still runs.
I would start cleaning all parts that can be dis-assembled. change all hoses, including vacuum hose, clean up all electric connections.
replace all filters, oil, air.........., replace all fuilds, brake, trans, coolant, engine....... and what ever else you come across.

May 22, 2009 | 2008 Toyota FJ Cruiser

2 Answers

High engine idle while in gear, clutch depressed


There is a Subaru Technical Bulletin on this problem (11-89-08) for a ECU reprogrammation that will cure this problem also found on a lot of 2.5 engine for 2008 what ever the model.

May 20, 2009 | 2008 Subaru Outback

1 Answer

Grinding sound on pressing clutch in at high revs


The grinding sound may be a throw out bearing or the pilot bearing. The sticking throttle problem sounds like a linkage or cable binding up from possibly damage due to the impact from the accident.

Feb 05, 2009 | 2008 Toyota Yaris Sedan

Not finding what you are looking for?
2008 Toyota Camry Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7001 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...