Question about Chevrolet Aveo

1 Answer

Astra settings in nm for head - Aveo Chevrolet Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 4 Answers

Wich engine is in Astra and year of production.I have some manuals for Opel.

Posted on Jan 22, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The cylinder head torque settings on a nissan cabstar diesel 2010


Head Torque settings (Don't need to renew bolts)

Stage 1, Tighten 39-44 Nm
Stage 2, Tighten 54-59 Nm
Stage 3, Tighten 90 degrees

Jun 26, 2016 | Nissan Cars & Trucks

1 Answer

What is the torque settings for polo bah motor big ends :mains and cylinder head


CHECK BELOW..
25458898-ms2db0pp00uj21y1nio4xcxs-1-0.png

Tightening torques
Bolted connections Tightening torque
Bolts, nuts M 6 10 Nm
M 8 20 Nm
M 10 45 Nm
M 12 60 Nm
Deviating from above
Exhaust pipe to manifold 40 Nm
Installation
Note
t Only remove the new cylinder head gasket from its packing immediately before installing.
t Handle the new gasket with extreme care. Damaging will lead to leaks.
- Place a clean cloth in cylinders so that no dirt or emery cloth particles can get in between cylinder wall and piston.
- Also prevent dirt and emery cloth particles from getting into the coolant.
- Carefully clean cylinder head and cylinder block sealing surfaces. Thereby ensuring that no scoring or scratches are formed (when using abrasive paper the grade must not be less than 100).
- Carefully remove metal particles, emery remains and cloths.
- Set No. 1 cylinder piston to TDC and then turn crankshaft back slightly.
- To centralize, screw guide pins from 3450/1 into front outer holes for cylinder head bolts-flechas-.
- Place the new cylinder head gasket in the centralizing pins -A-. Lettering (Part No.) must be readable.
- Fit cylinder head, screw in 8 remaining cylinder head bolts and tighten by hand.
- Remove the guide pins with tool 3450 by the bolt holes. To do this, turn the tool left until the pins are removed.
- Fit remaining cylinder head bolts and tighten hand-tight.
- Tighten cylinder head in tightening sequence as follows:
- Tighten all bolts to 30 Nm.
- Then tighten all bolts a 1//4 turn (90 °) further using a rigid wrench.
- Then tighten all bolts again a 1/4 turn (90 °) further.
Note
There is no requirement to retighten the cylinder head bolts after repairs.
The rest of the assembly is basically a reverse of the dismantling sequence.
Note
When the camshaft is turned, the crankshaft must not be at TDC. Danger of damage to valves or piston crowns.
Installing toothed belt and adjusting valve timing > Chapter.
Filling with new coolant > Chapter.
- Interrogate fault memory > Chapter.

Feb 21, 2015 | 2006 Volkswagen Polo 1.6

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Removing head on 1999 passat 1.8


Timing belt set-up diagram on 1999 VW Passat 1.8

tdisline_517.jpg


tdisline_518.jpg

Timing chain in cylinder head set-up:

tdisline_25.png
tdisline_26.png
Cylinder head instructions:

Tightening sequence

tdisline_519.jpg
Renew bolts!
Stage 1: Tighten = 40 Nm

Stage 2: Tighten = 60 Nm
Stage 3: Tighten = 90 degrees
Stage 4: Tighten = 90 degrees

May 12, 2011 | 1999 Volkswagen Passat

2 Answers

Dear expert What are the cylinder head bolt torque settings for the 4.0L MFI straight 6 engine? Regards Dave


Here are the specs and sequence:

0900c152800a9943.gif

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

  1. Tighten all bolts to 22 ft. lbs. (30 Nm).
  2. Tighten all bolts to 45 ft. lbs. (61 Nm).
  3. Retighten all bolts to 45 ft. lbs. (61 Nm).
  4. Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
  5. Tighten bolt 11 to 100 ft. lbs. (136 Nm)
  6. Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)

May 04, 2011 | 1996 Jeep Grand Cherokee

2 Answers

I have a 1998 Holden Astra eng noEL20B24119 and want to know the Head bolt torque settings and sequence. The engine is the transition model with twin tappet cover seals. has the torx star headed bolts.


I cannot find a EL20B in my data,but all Astra listed had the same head sequence as shown:

10 6 2 3 7

9 5 1 4 8

the torque specs for the C20XE,C20NE,X20XEV were all
25nm(18lb/ft),-then 90 deg,-90deg,-90deg.
Z20LET were as above plus an additional 15deg.
Same data for smaller and larger engines(except a couple that were 45deg instead of 15)
Make sure that you replace the head bolts with new,they are torque to yield bolts that are designed to stretch to 'plastic' state,and should not be reused.
Put grease(graphite if you have it) under bolt heads and washers,oil the threads.
Usually the head sets come with the torque specs.
I hope this helps you.

Apr 02, 2011 | Honda Accord Cars & Trucks

1 Answer

What are the torque settings for the head bolts on a 1999 ford taurus 3.0L.


This is the factory torque adjustment procedure for a 3.0L, also i post you the bolts tightening sequence. i hope that this could help you

  1. Tighten in five steps (refer to illustration in Cylinder Head Installation for tightening sequence):
    • Tighten in sequence to 47-53 Nm (35-39 Lb-Ft)
    • Then back off all bolts 360 degrees
    • Tighten in sequence to 27-33 Nm (20-24 Lb-Ft)
    • Rotate 85-95 degrees
    • Rotate an additional 85-95 degrees.
  2. Tighten in two steps:
    • 20-30 Nm (15-22 Lb-Ft)
    • 26-32 Nm (20-23 Lb-Ft)
  3. Advance 3/4 to 1 turn after gasket contacts sealing surface or tighten to 13-15 Nm (10-11 Lb-Ft).
  4. Tighten in two steps:
    • 7-15 Nm (6-11 Lb-Ft)
    • 26-38 Nm (20-28 Lb-Ft)
  5. Refer to illustration in the Cylinder Head Installation procedure for tightening sequence.

ganyapr_22.gif

Mar 20, 2011 | Ford Taurus Cars & Trucks

1 Answer

Cant find out the cylinder head torque settings for a 1997 2.0L ptrol 24 valve vitara


Cylinder head instructions
Cylinder head
Renew bolts No
Stage 1 Tighten 35 Nm
Stage 2 Tighten 75 Nm
Stage 3 Tighten 105 Nm

Feb 13, 2010 | 1999 Suzuki Vitara

1 Answer

Head stud torque


cyl head torqes.1st stage 29 nm. 2 nd stage 57-67 nm. 3rd stage slacken off 360 cegrees, 4th stage 29 nm. 5th stage 64-74 nm. intake and exhaust valve clearance .38 mm hot setting. hope it goes ok.

Aug 14, 2009 | 1987 Nissan King Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...