Question about 2006 Toyota Camry

1 Answer

How to locate timing on the counter weigth balancer

I cannot see how to put the two balancer on the bottom of the crankshaft gear

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 61 Answers

Check for all marks or make your own. to replace

Posted on Jan 22, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: how to remove the counter balance gear on the crankshaft

The best advice is to have it pressed off and then pressed on to the other shaft. Hitting it WILL damage the gear.

The graciousness of a FixYa rating for my assistance would be greatly appreciated; Thanks in advance.

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Echo 1.5 harmonic balancer will not stay tight


there is a nut that screws on to tighten it,look closer

Apr 25, 2015 | Cars & Trucks

1 Answer

How do I take a cam shaft sensor inside a GMC sierra distrubuter?


place engine on TDC by putting crankshaft balancer groove in line with timing cover pointer slot this is located between water pump and power steering pump then remove cap mark rotor pointer location for install indexing then remove drive pin onshaft that hold drive gear on mark gear to put on the same way remove shaft replace sensor reassemble

May 13, 2014 | GMC Sierra Cars & Trucks

1 Answer

How to install timing chain


yes check for all marks. put on tds

Jan 22, 2013 | Cars & Trucks

2 Answers

2001 mitsubishi galant crankshaft position sensor


the camshaft position sensor is located behind the harmonice balancer remove balancer and timing cover once removed you will see it u will also have to remove the crank gear and timing belt be sure to reset the timing or mark the gears before removal hope this helps

Jan 19, 2013 | 2001 Mitsubishi Galant

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on


the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

2 Answers

Location crankshaft sensor 96c1500 5.7ci


CRANKSHAFT POSITION SENSOR LOCATED NEXT TO THE STARTER.

Sep 16, 2011 | 1996 Chevrolet C1500

1 Answer

I need to correctly put a F250 with a 86 351 winsdor motor back in time? - time chain and gears


Not terribly complicated. Set the crankshaft at TDC on timing scale before you start, as a reference. If the cover is off just stick it back on there for a minute and same for harmonic balancer.
Once you have done that you should see a mark on the lower gear, either straight up at the top or straight down (if at bottom, put damper back on and turn till it points up.) You should be able to find a corresponding mark on the cam gear. That mark needs to point down, directly at the one on the crank gear. To do that, loosely install the cam gear on the cam and turn it till it lines up. Remove the cam gear and place the chain over it and the bottom gear. do not change the crank or cam position. To check for proper alignment, put the balancer on the crank ant turn it exactly two turns. the marks should return to original indexing. Make sure you have everything tightened up and then put the remainder of the engine back together.

Dec 08, 2009 | 1986 Ford F 250

3 Answers

4.3 vortec engine , engine noise, knocking or tapping on top of engine, not when cold , but starts noise when it heats up, and gets louder as it gets hotter and hotter!!! Sounds like noise is in the center...


The knocking or ticking is going to determine if it is in the top end, lifters, push-rod or rocker arm issue or the bottom end that would include pistons or bearings.
If it is a ticking noise, it will more than likely be a valve train issue.
If a knocking noise, piston or crankshaft related problem.

Attached is a web site that you can listen to a piston slap which is a known issue for your 4.3.
Listen to the noise and see if it sounds similar to your problem. A piston slap will generally sound as though it is coming from the central area of the engine.
Listen to the recording and let me know.
Regards,

Apr 19, 2009 | 1996 GMC Jimmy

1 Answer

How to remove the counter balance gear on the crankshaft


The best advice is to have it pressed off and then pressed on to the other shaft. Hitting it WILL damage the gear.

The graciousness of a FixYa rating for my assistance would be greatly appreciated; Thanks in advance.

Jan 25, 2009 | 1998 Toyota Camry

2 Answers

How to find timing belts marks toyota rav4 2l


there is a hole in the cam gear that if you look through it with a mirror and light you should see a small notch in the cam cap. on the crank gear there is a small divot between the teeth just to the left of the keyway notch that should align with a small dimple on the oil pump cover

Oct 14, 2008 | 2000 Toyota RAV4

Not finding what you are looking for?
2006 Toyota Camry Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...