Question about 2004 Ford F150

1 Answer

Remote key pad light stays on all the time

Remote key pad works fine but red light stays on all the time

Posted by on

  • Steve S
    Steve S May 11, 2010

    Which red light ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

Have you replaced the battery

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vehicle will start with remote but not with key. the theft light flashes with key


Try locking and unlocking the doors with the key fob to see if it corrects the problem. You can also try using the key and locking and unlocking the drivers door only

Feb 15, 2016 | 2008 Ford Escape

1 Answer

Red light on after replacing the battery in a subaru remote key


You put the battery or batteries in upside down, wrong polarity.

Jan 12, 2013 | 2002 Subaru Outback

1 Answer

The light in the dashboard is staying red for the brakes. Ihave checked the brake , they are released so why is the brake light staying red olease


Because the brake pads have sensors on and when they wear down too far, they activate the brake warning light. Time for new brake pads!

Jun 21, 2011 | 1995 Oldsmobile Cutlass Supreme

2 Answers

Keyless entry isn't working and alarm was tripped


Check your door latches. Since the light stays on, one of them isn't reading properly. Once you get that fixed, the remote should work. The light problem could be related. The computer thinks the door isn't shut so that part of the system thinks you aren't moving.

Mar 20, 2010 | 2002 Ford F350 Super Duty DRW Reg. Cab

1 Answer

2003 ram 5.7 electrical problem


run a status check on the pcm. sometimes those probs are in the computer. the loghts will come on when the remote is activated, and the door locks should lock automatically when you start to drive. if that doesn'tr happen, suspect a computer glitch.

Jul 20, 2009 | 2004 Dodge Ram 1500

1 Answer

My renault laguna 1999 rt remote key fob wont work?


IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Jul 09, 2009 | 2004 Renault 181

1 Answer

Ford Focus T Reg (UK) Key Fob Not Working.


it might be the 60 amp black fuse my partner just said

Apr 13, 2009 | 2000 Ford Focus

1 Answer

Brake light stays on


check the brake fluid level, if its low the light will be on. Usually when the brake pads wear down the fluid will become low and thats about the time to change the pads. You should be able to add some fluid though and be ok for a bit. If you hear any funny sounds like grinding or squicking (sp) then its time for brakes.

Dec 29, 2008 | 2005 Chevrolet Cavalier

3 Answers

Focus remote key fob not working


this info would cost you £30.+ at ford Radio Frequency Programming Instructions:
  • Insert the ignition key and turn from position II (Ignition) to position 0 (All off) and back four times within three seconds.
  • Remove the ignition key. The locking control system is now in "learn mode" for the next 20 seconds and the red warning system LED (By the clock) stays on continuously to indicate this.
  • During the 20 seconds press one of the transmitter buttons. The remotes signal and code number is learned by the locking module and is indicated by flashing the warning system LED.
  • Wait until learn mode times out (20 seconds) or switch the ignition back to ON.nfrared Programming Instructions:
  • Put your key into the ignition and turn to position 1 (Radio). After approximately 10 seconds the red alarm control LED (next to the clock) should illuminate. As soon as it comes on remove the key from the ignition - the LED should remain lit.
  • Point the remote's "eye" at one of the front door sensors and press the rear button until the light on the transmitter illuminates (Keep the button pressed)
  • With the rear button held in press the front button 4 times then release both at the same time. The control lights in both clock and fob will flash 4 times to indicate programming complete.
  • Turn the ignition back on to exit programming mode

Nov 28, 2008 | 2000 Ford Focus

2 Answers

VW passatt warning lights staying on


Check the wires that are going to the brake pad sensors.Some shops will install pads that don't have the sensor connections on them, causing this light to stay lit.

Oct 17, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21986 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...