Question about 2004 Ford Explorer

1 Answer

Ford 2004 explorer immobiliser module location?

Cant start it need to locate immobilizer .

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Are you using a key copy, w/o a chip in it? if so, it will immobilize. if it's a new key "with" a chip, it needs to be programmed.

Posted on Jan 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

moparownr
  • 667 Answers

SOURCE: location of computor module for keypad entry

the keyless entry module is on the drivers side of the truck up under the dash directly above the emergency brake. The tag should have a 5 digit number in bold, that is your door code.

Posted on Mar 23, 2009

kallumin
  • 1 Answer

SOURCE: 97 ford taurus air bag module location

It"s in the steering column...

Posted on Apr 01, 2009

  • 383 Answers

SOURCE: where is the ignition module located on the 1996 ford contour?

tragik nc: In looking this car up in both the 4 and 6 cyl configurations, Ford said that the ignition control module is no longer a separate component. It is actually integrated into the PCM (power control module)
This is located in the right rear corner of the engine compartment behind the power steering reservoir.
Good Luck, mybunkey>>>>>>>>>>>>>>>>>

Posted on Apr 20, 2009

localwonder
  • 6784 Answers

SOURCE: cant seam to locate were the fuel filter canister is on the 2003 ford explorer xlt

the filter is located along the frame near the tank. its connected in between the fuel lines leading along the frame.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the body control module located on a 2002 Ford explorer XLT


It's called a GEM - generic electronic module .It is located behind center of the instrument panel .
SECTION 419-10: Multifunction Electronic Modules 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 10/07/2004 Module - Generic Electronic (GEM)/Central Timer (CTM) Removal
  1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .
  1. Remove the audio unit. For additional information, refer to Section 415-01 .
  1. Remove the center instrument panel finish panel.
    1. Remove the screws.
    1. Remove the center instrument panel finish panel.
    • Disconnect the electrical connectors.
  1. Remove the GEM/CTM.
    1. Remove the screw.
    1. Disconnect the four connectors from the GEM/CTM.
    1. Remove the GEM/CTM.

Feb 18, 2017 | 2002 Ford Explorer

1 Answer

Need a wiring digram for a 2004 Ford Explorer starting system


Sorry but I can't help with a diagram.

I think your car could be a CANbus system where there is no direct connection between the starter switch and the starter motor. Starting is likely to be controlled by a relay which is energised by an ECU if the immobiliser has been disarmed, the starter switch only serving to send a signal to a nearby computer for starting to take place.

If this is your system it is possible to check the switch, relay, starter in the traditional manner but glitches in the system will need specialist diagnostic equipment to locate.

Apologies if I have guessed wrongly...

Aug 10, 2016 | 2004 Ford Explorer

1 Answer

Need diagram to locate fuse for cruise control 2004 ford explorer.


You should be able to get the information by going to Google and asking for location of the fuse for cruisecontrol ....

Jul 24, 2016 | 2004 Ford Explorer

1 Answer

I replaced immobilizer coil . still getting theft light code 11


Reading Ford Immobiliser Codes PATS - YouTube

? 2:00
https://www.youtube.com/watch?v=0kBZeBbb9PM
Mar 31, 2011 - Uploaded by Ask The Mechanic
How to read Ford Immobiliser codes when your car won't start. PATS (PASSIVE ANTI THEFT SYSTEM) http://www.askthemechanic.co.uk. ... and milage appeared, but red light still flashing 1:6 Found Fordwiki, and Youtube, ... a scanner with Body Control software you would get a code of B10D7 for code 11.Missing: taurus

Starting difficulty due to defective anti-theft control module ...

repairpal.com > Problems > Kia > Sedona
2003 Kia Sedona120,000Visitor ... no knowledge of this easily findable problem with the Vehicle Immobilizer Control Module. ... Upvote (11) .... I have replaced the temp. sensor and I am still getting a PO118 code. ... Check Engine Light Stays on since purchase of 02 kia sedona with 89,000 mileage. ... Ignition Coil May Fail.

KCSS-Transportation-Technology - Ford Passive Anti-theft ...



Jan 21, 2016 | 2003 Ford Taurus

2 Answers

2004 ford explorer stalling


if the engine dies at idle like when you hit the brakes at a stop light, most likely itis your IAC idle air control valve. It's the little cyllindrical valve has 2 bolts and an electrical plug located on your throttle body. Unplug it and unbolt. I cleaned mine thoroughly with parts cleaner and also lubricatd with wd40 and put it back on about 18000 miles ago and not an issue yet. fixed my problem. I ll get a new next time

Feb 25, 2010 | 2004 Ford Explorer

1 Answer

IMMOBILISER


The key has a micro chip in it that transmits a signal/code to the anti-theft module/immobilizer. There have been cases where the immobiler/module has forgotten wht code it should respond to or the chip in the key has gone bad. Either way the vehicle will have to go to the dealer for repair as they will have to reprogram the immobilizer for the new key and vice versa depending on which of the 2 items went bad. Hope this helps u

Jul 17, 2009 | 2002 Hyundai Santa Fe

3 Answers

Need keyless entry code for a 04 an 99 ford explorer


On your 99 model the module is located behind the left quarter trim panel,mid-way.You maybe able to see it by removing the speaker cover or the cupholder on top. The module will have a sticker with a 5 digit code.
On the 04 the model is behind the right quarter trim panel toward the front about even with the right rear door stricker.

May 17, 2009 | 1999 Ford Explorer

1 Answer

Replacing the control module on my 1997 ford explorer


the module is located behind the dash just to the left of the radio. remove the two screws below the radio and the dash panel snaps out and you can access the module

May 10, 2009 | 1997 Ford Explorer AWD

1 Answer

Ford 1996 Immobiliser bypass


Most aftermarket alarm companies make a bypass module for the immobilizer. Check with your local car audio/alarm retailer

Jan 04, 2009 | 1996 Ford Escort 4 Door

1 Answer

Gem module


behind the pass side air bag

Nov 19, 2008 | 2004 Ford Explorer Sport Trac

Not finding what you are looking for?
2004 Ford Explorer Logo

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...