Question about Cars & Trucks

1 Answer

I have touched the ignition wire against the ariel lead on the back of the streo now the stoeo wont work and the car wont start now can you help?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check your fuses under hood and in passenger compartment refer to service manual.as to location of the respective fuses and or fusible links.

Posted on Jan 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: car wont start

I noticed you replace the crankshaft sensor, but not the CAMshaft sensor.
The Ignition module takes the input of both sensors to tell the coil when to energize.
This sensor should come up as an error code when you attach a obd reader.
Even if your light is not on - there may be a code. If it is not your vehicle originally, some people pull the bulb!

Posted on Jan 22, 2009

  • 3 Answers

SOURCE: wont start. no fire from the coil.

check the pick up in the Distributor

Posted on Mar 01, 2009

  • 4 Answers

SOURCE: car wont start .

You will not be able to hear the fuel pump on that model. First you have to determine if you get fuel and have spark. If it is a fuel problem, replace the DME relay first. Very common. They act up and fail without warning. Part is cheap and located in the fuse box. Next would be the fuel pump.
If it is spark related it may be the Flywheel Reference Sensors. There are two and the cost about $100 each.

Good Luck.

Posted on Apr 22, 2009

clarktravis8
  • 74 Answers

SOURCE: Changed plugs now car wont start

You can try this it should resolve you issue from the front passenger side going to the driver side use 1-3-5. from the rear passenger to driver side use 2-4-6 The plug wire is 1,4,5,2,3,6. wutxtye0rjd9d9ekmodqt1eoxkvn9hr9qjz1l3dabggyud7sdgr36czsrfxqenadhnijx9nfayi+sz1sug0aaaaasuvork5cyii=

Posted on Apr 24, 2009

  • 192 Answers

SOURCE: car wont start after the alarm is disabled

is the alarm factory or after market need to know. very important..

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to change a broken electric ariel on a saab


my electric Ariel stopped working and I was quoted £87 to replace it I bought a replacement on ebay for £13 its a simple fix just undo the Ariel nut on top of the car rear wing get someone to sit in car and push radio button old ariel starts to come out simple assist it until it has completely come away from car put new lead into hole then get person in car to switch of radio and feel the ariel start to be pulled back into place be carful to keep it straight as it enters then replace locking nut total time less than 5 mins cost £13 plus one person to assist easy fix

on May 07, 2015 | Saab 9 Cars & Trucks

1 Answer

Dodge 440 no crank no start


Check the ignition switch wire . from the ignition switch to the starter. Try jumping the starter. The lead that the battery cable hooks to and the lead the ignition wire hooks to. use a screwdriver and touch both.

Aug 26, 2016 | Dodge Cars & Trucks

1 Answer

Turn igniton and nothing happens gauges work but want start


Does the acc position work. if so....Under the dash there are two wires, one is red and the other is red/black, these are a heavy gauge wire so you wont miss them, strip some sheilding off of each one and touch them together with your ignition in the acc/on position, does the starter try to turn? (it wont start unless the clutch is pressed) if so your ignition switch is bad, just take some leads off of those two wires and run them to a momentary switch that will carry the voltage and use that switch to start your car

Feb 24, 2013 | 1996 Volkswagen Jetta

1 Answer

I was driving when my engine just stoped i tryed to start it but it wont start the engine will turn over but it just wont start


it is possible the points in the distributer cap have failed, or worn. check your spark plugs (you will need 2 people for this) or even just your leads by having one person turn the engine over and the other holding 1 lead (just take one off at a time) against the engine block it should throw a spark and arc to the block ******DONT TOUCH THE SPARK IT HURTS****** if you dont get a spark then it is most likly a distributer problem. Hope thes helps

Feb 09, 2011 | 1991 Mitsubishi Galant

1 Answer

The engin will not turn over intermittently. I had the dealership check the batter, the starter and the alternator. All came out good. They could not get the car not to start so they could not fix it. ...


Try starting in Neutral instead of Park. If this works, the transmission range switch (sometimes called a neutral safety switch) is faulty in Park.

Next, you can try a remote start switch (available at auto parts stores) or a jumper wire to bypass the ignition switch. First make sure transmission is in park or neutral. You will be jumping from the battery positive terminal to the starter solenoid. The starter solenoid terminal has a black wire with a white stripe connected to it. (This terminal is visible just to the left of the automatic transmission dipstick tube.) Remove this wire and connect one end of the remote start switch wire (or jumper wire) to it. Connect the other end of the remote start switch wire to the battery positive terminal. Activate the remote start switch and see if the starter will crank. (If using a jumper wire, briefly touch the other end to the battery positive terminal and see if cranking will occur). If the starter works then you have a problem in the ignition switch, or starter cut-out relay.

The starter cut-out relay is located on the back of the driver's under dash fuse/relay box in the left wall kick panel. The ignition switch also has wire leads that plug into the back of this same fuse box. You can disconnect the wire leads and test the ignition switch with on ohm meter from this point.

Jan 23, 2011 | 2003 Honda Odyssey

1 Answer

My olds 1992 88 stopped running. changed the fuel filter and drained all of the old fuel (which wasuper rusty and contaminated). the car seems to want to start now but wont. i have been told to change the...


have you got a good spark- take out a plug and lay it plugged into the lead on top of the engine so the tip is earthed (touching the engine) and crank it over - DO NOT TOUCH THE PLUG WHILST CRANKING AS IT GENERATES MASSIVE ELECTRICAL VOLTAGE..............
if it sparks its probably a fuel problem still and not ignition/electrical.

Sep 18, 2017 | 1992 Oldsmobile 88

2 Answers

Car turns over but wont start it is a kia sedona


the car will not start if the immo light is not lit. sometimes turning the key back and forth or removing it and locking then unlocking the car can sometimes remedy this.

Jan 10, 2010 | 2004 Kia Sedona

2 Answers

95 jetta wont start unless you pop start it i changed the starter i have all the power just when i turn the key nothing


check your fuses under the hood and under the dash
check polarity of battery (if you unhooked booth leads)
is the battery any good?
you probly conected the leads to the starter incorectly (recheck them)

(the following asume your tur n key ignition system is functioning properly)
to test your tur n key system simply hook up a test light to the small lead running to the starter cylynoid "while the wire is disconected" and have a friend turn the ignition over. [dont furget to test the test light first lol]

or even got the wrong starter completly (usaly a store problem)
did you " bench test" the new/used starter befor installing it ?
iv goten brand new starters doa

is the ground strap hooked up ? is there corosian on the battery posts or any of the high amperage conections?

is the cylynoid on the starter or somewhere else under the hood?
cautiously try to bypass the cylynoid ie run a hot wire to the small lead on the cylynoid
(this can usaly be done by jumping from the main red wire on the starter to the hot lead of the cylynoid)

notes: when bypassing the ingnition system (jumping the cylynoid)
DO NOT have the ignition in the on postion and it is best to remove the lead from the cylynoid (incase of a short in the wire's some place)

if nothing remove the large red wire on the cylynoid and touch it directly to the starter lead itself (there will be a fair amount of spark when doing this its normal) but make shur you are conecting to the starter lead and not a gound point as this will cause exsesive sparking that isn't good
dose the starter tur n the engine over
back track untill you find the fault be it starter itself,cyclynoid,wiring,blown fuse,corosion,bad battery,

still cant find the problem take it to a shop!
hope i helped yah

Dec 14, 2009 | 1995 Volkswagen Jetta

2 Answers

86 transam runs perfect cold then like a dog if you start it hot


check for cracked dizzy cap ??and the carbon button in the middle

Sep 11, 2009 | 1985 Pontiac Firebird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...