Question about Cars & Trucks

Open Question

How do I replace the rear crankshaft seal and oil slinger on Mitsubishi canter 4d35?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 93 Answers

SOURCE: Rear Crankshaft oil seal

ref rear main oil seal pre size tool needed to fit seal this beds the seal into housing should be no need to trim ends fit rear main cap fit seal housing loose fit tool lubricate seal revolve anticlockwise nip seal cap screws a bit at a time keep well lubricated seal will then find its correct position and sit flush

Posted on Oct 30, 2009

  • 7353 Answers

SOURCE: I was told I have

Well sometimes.... the front crankshaft seal is usually called a crank seal, or the front timing cover seal but the rear crank seal is (usually) called the Rear Main crank seal. In order to replace the rear seal , the transmission will need to be removed. If its the front, then the harmonic balancer will be removed. $380 sounds cheap. As you will need a oil seal, oil pan gasket, oil, filter, labor and tax. Maybe even a lower engine mount.

Posted on Feb 01, 2011

Testimonial: "Thank you sooo much!! This mechanic has been in business for 45 years and has been the president of an antique car club for many years..."

  • 5 Answers

SOURCE: 1989 honda accord oil leeak cam/crankshaft

Camshaft seal must be replaced when the engine is cold. Take off valve cover and then the upper timing cover and take off the camshaft sprocket and the timing belt will come off too. Use a small screw driver to pull the old seal off and then force in the new one. Then pull back the sprocket and timing belt. If the engine is hot, the timing belt will not go back on the sprocket until the engine is totally cool down overnight. Or if you want, you can set the camshaft to TDC and take off the rocker arm assembly, take off the seal and put the new one on and reinstalled the bolts to the rocker arm assembly and then do the valve adjustment. From Sometime mechanic.

Posted on Nov 19, 2011

creg_912
  • 196 Answers

SOURCE: 2000 jaguar s-type 4.0 rear main seal or crankshaft oil leak?

sounds like a rear bell housing seal

Posted on Dec 12, 2011

emissionwiz
  • 75122 Answers

SOURCE: ineed mitsubishi canter 4D35 engine manual

We are a US based wesite and we have no diesels here in this model or make.

Posted on Mar 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the valve clearance for 4d35 engine


Mitsubishi canter engine

self adjusters
shimmed chart needed if a real problem

26333061-py5i4o5vftt3pvwug2gyetgw-1-0.jpg
6 INTAKE AND EXHAUST VALVE CLEARANCE INSPECT AND ADJUST
26333061-py5i4o5vftt3pvwug2gyetgw-1-1.jpg

Oct 30, 2016 | Cars & Trucks

1 Answer

NEED DIAGRAM FOR LOCATIONS OF CRANKSHAFT PULLY,OIL SLINGER AND SPRING.FOR 1983 MAZDA 2.2L DIESEL


Here is the procedure:-


  1. Remove setscrew from side of cylinder block.


  2. Remove oil pipe attaching bolts.


  3. Remove oil pump and strainer.
TIMING GEAR COVER



  1. Remove timing gear cover to case attaching bolts.


  2. Remove timing gear cover and gasket.

CAMSHAFT, CRANKSHAFT, IDLER & INJECTION PUMP GEARS



  1. Remove oil slinger and washers from crankshaft snout.
Using puller set 49 0839 425C or equivalent, remove crankshaft timing gear, Fig. 3.


  1. Position a clean rag between camshaft and idler gears, then remove cam gear lock bolt and washers.


  2. Using puller set 49 0839 425C or equivalent, remove cam gear from camshaft, Fig. 3.


  3. Remove idler gear to spindle retaining nuts and washers, then remove idler gear and spindle assemblies.


  4. Remove injection pump drive gear.


  5. Remove timing gear case to cylinder block attaching bolts, then the timing case.



CAMSHAFT




  1. Remove tappets from cylinder block.


  2. Remove camshaft thrust plate to cylinder block retaining bolts and washers, then pull camshaft from block.



PISTON & CONNECTING ROD




  1. Remove connecting rod bearing cap retaining nuts and bolts, then separate bearing cap from connecting rod.


  2. Using the wooden handle end of a hammer, push the piston and connecting rod assembly outward until piston rings clear cylinder bore. Remove piston and connecting rod assembly through top of cylinder block.


  3. To separate piston from connecting rod, remove piston pin retaining clips, then press pin from piston using a suitable driver.



CRANKSHAFT




  1. Remove rear oil seal cap retaining bolts, then the cap and seal.


  2. Remove main bearing cap to cylinder block retaining bolts, then the main bearing caps and thrust washers.


  3. Lift crankshaft from cylinder block.

Mar 26, 2015 | Mazda Cars & Trucks

1 Answer

Ineed mitsubishi canter 4D35 engine manual


We are a US based wesite and we have no diesels here in this model or make.

Mar 13, 2012 | Mitsubishi Pajero Cars & Trucks

1 Answer

How do I replace the rear seal on a cadillac cts


YOU NEED TO REMOVE FLYWHEEL REMOVE OIL PAN. REMOVE REAR OIL SEAL HOUSING BOLTS. USING THE PRY POINT LOCATED AT THE EDGE OF THE CRANKSHAFT REAR MAIN SEAL HOUSING SHEAR THE RTV SEALANT. REMOVE THE REAR MAIN OIL SEAL. INSTALL GUIDE PINS INTO THE TWO CRANK SHAFT REAR OIL SEAL HOUSING CORNER BOLT HOLES OF THE ENGINE BLOCK.INSTALL THE CRANKSHAFT REAR SEAL INSTALLING TOOL ONTO THE REAR OF THE CRANKSHAFT FLANGE. APPLY A 0.2 INCH 3MM BEAD OF SILICONE SEALANT TO THE REAR OIL SEAL HOUSING . INSTALL THE REAR HOUSING TO THE ENGINE BLOCK.REMOVE THE GUIDE PINS AND INSTALL THE HOUSING BOLTS TIGHTEN THE BOLTS TO 89 INCH LBS. REMOVE THE REAR SEAL INSTALLATION TOOL FROM THE CRANKSHAFT FLANGE.THEN INSTALL OIL PAN AND FLYWHEEL.

Sep 10, 2011 | 2008 Cadillac Cts

1 Answer

I was told I have to replace the crankshaft seal and oil pan gasket on my 2000 chevy malibu and will cost approx. $380.00. Also is the rear main seal the same thing as the crankshaft seal??? Thanks!


Well sometimes.... the front crankshaft seal is usually called a crank seal, or the front timing cover seal but the rear crank seal is (usually) called the Rear Main crank seal. In order to replace the rear seal , the transmission will need to be removed. If its the front, then the harmonic balancer will be removed. $380 sounds cheap. As you will need a oil seal, oil pan gasket, oil, filter, labor and tax. Maybe even a lower engine mount.

Feb 01, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

Rear barring an seal replaced


I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines 85553308.gif
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.
  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Oct 07, 2010 | 1994 Ford Explorer Limited

1 Answer

I have a 2006 Pontiac Grand Prix, it is supercharged 3800. I have about 115,000 miles on it and I change the oil every 3,000 miles, check fluids, regular preventative maintenance, etc. I noticed a small...


If it's oil, it's coming from the rear main seal.. I would go with this idea.

The seal doesn't cost much but the labor to get to it does.

To give you an idea what is involved the procedure is illustrated below from the service manual:

Removal & Installation 3.8L Engine To Remove:
  1. Drain the engine coolant.
  2. Drain the engine oil.
  3. Remove the oil pan.
  4. Remove the engine flywheel.
  5. Remove the rear oil seal housing and gasket. Rear seal removal 3.8L gm-03-38-1175.gif

  6. Remove the rear main seal by placing the housing face down on 2 blocks of wood. Using a drift tool and hammer tap the seal out of the housing.
To Install:
NOTE: Do not lubricate the rear main oil seal or the installation tool. Do not touch the sealing lip of the rear main seal once the protective sleeve is removed.
NOTE: Use a clean lint free cloth to clean the crankshaft sealing surface. Remove sharp edges or burrs that could damage the rear main oil seal. Remove burrs or sharp edges with a crocus cloth.
  1. Carefully remove the rear oil seal from the protective sleeve.
  2. Install the oil seal onto the seal driver EN-47623 or equivalent by placing the seal at an angle and twisting until it is fully seated.
  3. Install the seal into the housing using the seal driver EN-47623 or equivalent and driver handle J-8092 or equivalent. Apply downward force until the seal is seated. NOTE: Ensure that the housing gasket is installed correctly and that the oil passages are not blocked.
  4. Using a new gasket Install the rear oil seal housing on the engine being careful not damage the rear main seal. NOTE: The plastic inserts are used in production and are not needed for assembly.
  5. Hand tighten the bolts. Rear seal housing alignment 3.8L gm-03-38-1176.gif

  6. Place a straight edge on the crankshaft rear oil seal housing flange and the engine block oil pan flange. Using a feeler gauge check that there is no more than .0004 in (0.10 mm) step on each side. Rotate the housing to make the steps equal on both sides.
  7. Tighten the housing bolts 11 ft-lb (15 Nm) plus an additional 50 degrees.
  8. Ensure that the housing did not move out of specification. Repeat step 6 if the oil seal housing is not within the specified range. Replace the rear oil seal housing if the specified measurement can not be reached.
  9. Install the flywheel.
  10. Install the oil pan.
  11. Fill the engine oil and the cooling system.
  12. Check for leaks
5.3L Engine To Remove:
  1. Remove the flywheel from the crankshaft.
  2. Remove and discard the crankshaft rear oil seal from the rear cover.
To Install:
  1. Use clean engine oil to lubricate the outside diameter of the crankshaft rear oil seal and rear cover oil seal bore.
  2. Install the tapered cone and bolts of a J 41479 or equivalent crankshaft rear oil seal installer onto the crankshaft.
  3. Place the crankshaft rear oil seal onto the tapered cone.
  4. Install the threaded rod of the J 41479 crankshaft rear oil seal installer into the tapered cone. Rear main seal installer 5.3L gm-03-53-3872.gif

  5. Install the crankshaft rear oil seal by turning the handle of the J 41479 clockwise.
  6. Remove the J 41479 crankshaft rear oil seal installer from the crankshaft.
  7. Install the flywheel onto the crankshaft.
prev.gif next.gif--- I'm not sure what the exact cost would be as the hours were not listed for this procedure on my online resource.

Sep 02, 2010 | 2006 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...