Question about Cars & Trucks

Open Question

Peugeot 405 diesel timing marks

Can any one tell me the location of the timing marks on the peugeot 405

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: cam timing

Firstly with this engine being identified as an interference engine, I will not accept any responsibility if your engine gets damaged. You are free to take or leave this advice and the responsibility will be entirely yours.

Engine codes: D2H, D6A, D6B, D6D, DDZ, DKZ, DFZ.
Covering years 1989 to 1997.

  • Turn the crankshaft in a clockwise direction to about 10.00 o'clock on the mark on the camshaft sprocket. Good tip here, apply tippex to the sprocket mark.
  • Now slowly continue to turn the crankshaft and with the timing pin feel for the locating hole behind the camshaft sprocket.
  • You will find the camshaft location hole at about 8.00 o'clock.
  • When you have located the the locating hole behind the camshaft sprocket, insert the timing pin.
  • Now insert the timing pin in the crankshaft pulley.
  • You will find the crankshaft pulley location hole behind the sprocket at about 10.30 o'clock.
  • When both timing pins are in their locating holes, the top and bottom of the engine is in-line.
  • This information is only to set the engine up and not to change the timing belt.
  • I would advise that on these engines you change the timing belts at 60,000 miles or every 3 years which ever comes first. If for any reason the timing belt gets contaminated, change the timing belt.
Take care.

Posted on Dec 08, 2008

  • 8 Answers

SOURCE: Peugeot 405 1993 diesel estate

the alarm control unit is fitted under the drivers seat can be accessed from the rear foot well by putting seat fully forward .unscrew the two nuts holding the cover the relays are inside the unit.

this unit interfaces will tell the fuel stop solenoid to release (by applying 12 volts)

the fuel stop solinoid is on the main diesel pump under the bonnet - the exac location on the pump will depend on the make - but it should be cylindrical and have one wire connected to it - (i dont think peugeot were using multi wired coded soleniods in 93)

obivously if your car has the keypad immobilser you will know where this is - if it is the remote alarm immobilser the reciever is in the over head consol near the interior front light

Posted on Feb 13, 2009

  • 1 Answer

SOURCE: water leak to footwell of peugeot 405 diesel estate

if ur still interested, i had a similar problem. under the bonnet, just under the windscreen on passenger side, there is a black plastic cover. on mine it was cracked and had a hole in it, dont know how, must have been like that when i got it. anyway,it had been glued back together, obviously the glue had melted and the thing started to leak again. the water went through into the air filter which is just above the glove box. then it seeps down into the footwell.
hope this helps
kenny

Posted on Jul 19, 2009

Lloyd Six
  • 560 Answers

SOURCE: I ran my peugeot 406 out of diesel and i think

406 1996 Diesel would either be 1.9D, 1.9TD or 2.1TD

Each of these use a vacuum type distribution pump, which means once the fuel has managed to get to the pump via means of initial priming it looks after itself by constantly sucking fuel. If the engine stops after a a short time it could be a blockage caused by running very low on fuel. First thing to check is the primer system. You may have the squeazy balloon type or the purflux set up with a hand primer button. The issue is common to be at this point but hard to diagnose.

What I have done in the past is disconnect the pipe going to the main pump and given a seperate feed from a pipe submerged in a can of diesel, if it runs fine then it rules out mechanical and pump issues leaving it only to be a supply issue.

Regards

Lloyd

Posted on Dec 21, 2009

  • 1 Answer

SOURCE: hi i have a peugeot 405 diesel and the speedo

I had a similar problem with my old peugeot 405 diesel, something electrical was shorting and actually sparking in the engine compartment which in my case the garage fixed very easily. Same symptoms, the speedo flickered at low speeds but stopped at higher speed.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know what sort of oil my peugeot 405 GRD (1989) uses please. I'm a bit cartech useless 8-/


being diesel and its age i would recommend using a 10/40 or if its burning oil,say a pint every 1000 miles then use 20/50 most of the multigrades will be petrol and diesel.

Sep 03, 2010 | 1989 Peugeot 405

1 Answer

I replaced my cam belt and i need to set the timing, can u please tell me where are the timing marks?


on the crank/cam pulleys (small dots)on the outer rim,clean off and mark with chalk.

Jun 17, 2010 | 2005 Peugeot 405

1 Answer

Peugeot 405 ,2000cc car


petrol or diesel ?? think you may mean petrol ??2000cc with monopoint injection??

Nov 20, 2009 | 1991 Peugeot 405

1 Answer

Hi i have a peugeot 405 diesel and the speedo


I had a similar problem with my old peugeot 405 diesel, something electrical was shorting and actually sparking in the engine compartment which in my case the garage fixed very easily. Same symptoms, the speedo flickered at low speeds but stopped at higher speed.

Sep 21, 2009 | Peugeot 405 Cars & Trucks

3 Answers

1995 106 d peugeot cranck shaft timming marks on engine


I've uploaded a manual for 106 tud timing belt refitting:
http://www.gigasize.com/get.php?d=y1dnk2hbl8d
may be it can solve your problem

Sep 01, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 405 1993 diesel estate


the alarm control unit is fitted under the drivers seat can be accessed from the rear foot well by putting seat fully forward .unscrew the two nuts holding the cover the relays are inside the unit.

this unit interfaces will tell the fuel stop solenoid to release (by applying 12 volts)

the fuel stop solinoid is on the main diesel pump under the bonnet - the exac location on the pump will depend on the make - but it should be cylindrical and have one wire connected to it - (i dont think peugeot were using multi wired coded soleniods in 93)

obivously if your car has the keypad immobilser you will know where this is - if it is the remote alarm immobilser the reciever is in the over head consol near the interior front light

Jan 07, 2009 | 1983 Peugeot 504

2 Answers

Please,send me electrical diagram for peugeot 405 (2004)


Goto Amazon.co.uk

Search 'books' for Peugeot 405 (you will find the Haynes Manual). Make sure you choose the right one for your Year & type (Petrol/Diesel) = the wiring diagrams are in the back. Cost is about £20.

You can also borrow the Manual from your local Library for free ..

Dec 16, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...