Question about Peugeot 206

Open Question

Clutch pedal makes a cracking noise

54 reg 1.1 206 now and again when pressing clutch pedal it makes a cracking noise hard to get gears then it fine as if theres nothing wrong

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
lobsterman72
  • 91 Answers

SOURCE: tdi clutch pedal pushed all the way down but hard to shift gears

Check your clutch fluid level, sometimes a seperate reservoir (drivers side on firewall), some clutch systems take fluid from the brake system (check brake fluid). If thats ok then the clutch slave may be failing.
If the clutch fluid is low refill it and check for leaks (or just wait till the symptom comes back). If it's happens often then theres a leak in the line or the slave somewhere.

Posted on Jul 08, 2008

Ad
  • 231 Answers

SOURCE: hard to change gear

sounds like your slave cylinder for your clutch is by-passing.

Posted on Oct 18, 2008

  • 1779 Answers

SOURCE: Whining noise from clutch

The noise you hear is the 'clutch throwout bearing', which needs to be replaced.

Posted on Jan 02, 2009

Benimur
  • 6966 Answers

SOURCE: to change gears, I need to fully press down on my

Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Posted on Feb 18, 2009

  • 204 Answers

SOURCE: 1983 chevy s10 2.8 v6. underneath my clutch pedal

Have you got a hole in the floorboards????
It could be something loose in the clutch or just something ricochetting around the bell housing.

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Rav 4. 2002 reg Makes a grinding noise when driven until clutch is pressed to floor the noise disappears


clutch ,slave ,throw out bearing going bad --transmission shaft bearing --bad gear --but would look into clutch since you have o push to floor to have noise stop

Oct 27, 2016 | Toyota Cars & Trucks

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

2 Answers

Squealing noise stops when i push in clutch pedal we were on the interstate and suddenly i had no clutch pedal we got off the street it was hard to get it out of gear i checked the fluid it was fine...


Sounds like a bad Throw Out Bearing.. Needless to say.. it has to be repaired.

Depending on mileage.. may as well replace the clutch/pressure plate.. and have he flywheel looked at.. change the tranny oil.. check the u joints.. rear end etc..

Best of luck!

Apr 09, 2011 | 1997 Chevrolet Camaro

1 Answer

Hi, When clutch pedal is depressed, its very hard to get into gear also make a gear scraping noise when i select reverse


First have the linkage from the clutch pedal checked out then if no result have someone check out your clutch it may be worn out.

Apr 05, 2010 | 2005 Peugeot 405

1 Answer

I have a 89 toyota pickup 4 speed. When I'm stopped at a stop light, and let out on the clutch it seems like it has lost pressure. When I'm shifting down the road it shifts fine. I checked the fluid and it...


this sounds like the clutch slave is goin out, this unit is on the outside of the transmission. Possibly losing pressure!! Your transmission does not use transmission fluid, but instead gear oil. Have the following checked:
1. Clutch Slave (possibly worn)-this will cause soft or hard clutch pedal feel, slipping clutch, unintended clutch release, hard gear engagement, no/insufficient clutch movement.

*2. Clutch pedal Mounting Plate (possibly cracked)-this will cause improper gear engagement, hard gear engagement, soft pedal feel, insufficient clutch movement.

*this plate is located above the clutch pedal itself, apply pressure on the pedal with one hand while inspecting the plate for fatigue cracks(use a bright flashlight). This is very common on these models. This problem will eventually get worst and most mechanics never figure this out.

more questions email me at gimconsulting@ymail.com!!

Mar 15, 2010 | 1989 Toyota Pickup SR5

1 Answer

Peugeot 206 NEW clutch pressure and clutch plates were replaced including the bearing. Clutch is making a rattling noise but not when pedal is down. Having difficulty getting into 1st and 2nd gears....


its likley to be the clutch center plate cush springs are loos and the center plate is warped so wnen you try to get into gear the clutch is draging the gear box around,,,bipping the clutch stops the clutch spinning so no noise! all you can do is strip the lot down again and fine the fault and fix it

Feb 08, 2010 | 1987 Peugeot Liberte

1 Answer

I have a ford escort r reg td,the trouble is the gears is hard to go in to second.i have been told it might be the release bearing.what do u think? CLUTCH CABLE BEARING SELECTOR?


Pretty hard to tell you it's a release bearing without hearing it but unless release bearing is in very bad shape & making lots of noise, it's very unlikely that is the culprit here. Does the clutch disengage properly, as in car doesn't creep when pedal depressed? Check master cylinder & slave cylinder movement, perhaps bleeding slave will help, but if it's only in second gear that the problem is occurring then I'd give linkages a real good coat of lubricant & see if that helps at all.

Sep 09, 2009 | 1998 Ford Escort

1 Answer

Just bought 99 Hombre. My clutch pedal dose not work right


yes you can adjust the clutch unless it is already adjusted as far as it can be then you may have to replace it

Aug 30, 2009 | 1999 Isuzu Hombre

3 Answers

Clutch noise and stiffness


it sounds like your clutch release bearing has or is colapsing.when you press the clutch the release bearing is under the most load hence the noise.gearbox out i,m afraid.Can you still get gears ok ?.Also the pedal box,s are prone to break on polo,s ,the symptom for that is like a squashy pedal and hard to get gears.if you can look up at the top of the clutch pedal where the cable mounts see if the bracket the cable fits in to is broken away at the top.

Jan 26, 2009 | 2001 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

mike hayward

Level 2 Expert

279 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...