Question about Ford Futura

Open Question

Fuel pump replacement for my ford falcon au 98 wagon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22265 Answers

SOURCE: removing alternator 1993 ford falcon EA wagon

first disconnect battery,remove wiring loom from altenator the slacken V belt tensioner bolt so altenator swings free then undo the two bottom bolt or one long one depending on model.easy ,now the difference between sunday mechanic and a mechanic undo the two screws that hold the regulator/brush set housing and renew the brushes providing the commutator is servicable.

Posted on Nov 20, 2008

Ad
  • 1 Answer

SOURCE: 98 ford explorer fuel pump pressure

hello i have 1996 ford explorer this promblem is computer display [air ride switch off ]signal all time /////
please answer

Posted on Nov 26, 2008

angelo63
  • 129 Answers

SOURCE: will not go into reverse gear

if u have no reverse at all its time to change trans

Posted on Dec 16, 2008

  • 6 Answers

SOURCE: How do you replace a driving belt on a 1999 AU ford falcon

start by unplugin the electric fans then remove the two 10mm bolts holding them in, the bottom of the fans are held in by a slot that they sit in so after you remove 2 bolts just lift the fans out. then you will see a tensioner i think it has 3/8 drive square hole in it( could be 1/2'' drive) just pull it down with a long bar with a 3/8 end on it to release the tension, while doing that slide the belt of,. if your car doesnt have a picture diaghram on the under side of the bonnet for drive belt routing draw a picture incorprating all the pulleys an how the belt goes around them. once the belt is of put the new one on exept over the power steering pump pulley, then pull on the tensioner again to release tension and slide the belt over the p/s pulley. these instruction are for the 4.0l falcon motor, the 5.0 v8 is really similar

Posted on Apr 22, 2009

localwonder
  • 6784 Answers

SOURCE: remove fuel pump from tank ford windstar 98

To gain access to the fuel pump, it is necessary to remove the fuel tank.

  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram for trailer 2005 falcon wagon from car to trailer plug


Depends on plug type and number of Pins used.
Is it 5 pin or a 7 pin round plug or a rectangle plug ?

http://www.narva.com.au/products/browse/wiring-diagrams

Dec 24, 2016 | 2005 Ford Falcon

1 Answer

Wiring a trailer into a 2005 falcon wagon


http://www.narva.com.au/products/browse/wiring-diagrams

Dec 24, 2016 | 2005 Ford Falcon

1 Answer

AU Falcon turn over no fuel pump no start could it be the transponder in key


Check fuel cut-off switch if fuel pump is not turning on and you have checked the fuses.

May 20, 2014 | Ford Falcon Cars & Trucks

1 Answer

Au falcon idles in park but put into reverse or drive and stalls


Low fuel pressure. Check for a clogged fuel filter or faulty fuel pump. NOTE: sometimes the pump will run, but is still too weak to hold enough pressure to run and engine. Inspect the fuel system.

Dec 05, 2013 | Ford Falcon Cars & Trucks

1 Answer

My partner has a 1999 Au ford falcon wagon' we just replaced the gear box in it an now it won't start, we also replaced plugs, leads, battery, coils an air/fuel sensor, its turning over but won't start. It...


it may be that its relearning its fuel map-also you may what to check to over for a vacume line that got pulled off in the process-cheers Denny

Nov 04, 2013 | Cars & Trucks

1 Answer

Fuel pump in 98 el ford falcon v6 not working, have squirted fuel down breather nd car starts then dies, dont sound like fuel pump working, have cleaned contacts to pump, still not working, seems like it...


not sure on falcon but on many ford models they use a plastic impeller in the fuel pump .. that works fine until you run out of gas .. that could be just rounding a corner with the gas low ... once the pump runs dry the impeller is damaged quickly and you have just lost an expensive fuel pump .. if the pump jambs then it will likely blow the fuel pump fuse ...you can check with a voltmeter to see if you are getting power back there .. if so and it still doesn't work then start looking for a new pump ..its not a safe job changing the pump in some models .. really hard if the tank is full ..

Feb 22, 2010 | 1992 Ford LTD

3 Answers

EF FORD FALCON NO FUEL GETTING TO CARBI


The fuel pressure relay in the engine is not working or the fuel pressure relay is not working .
Try to replace the fuel pressure relay or soleniod in the engine area.

IF this does not work , Check the timing of the engine.

Mar 27, 2009 | 2002 Ford E-Series

3 Answers

Fuel Filter blockage


hi jesse,
the first time i sent this the system overloaded and i had to try again
it is located under the car just behind the diff right up high with push fuel joiners(possibly thread on one end) when i had the same problem, it was infact the fuel pump, because the AU use a fuel pump that requires fuel as a lubricant, it is located in a small pot in the fuel tank that is filled from your return line. if you run low on fuel they tend to run dry and wear out. i tested my pump pressure by fitting a VL inline injection pump. as this worked i replaced the fuel pump(which in an AU is a very nasty job) and have had no problems

Jan 09, 2009 | 2005 Ford Futura

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...