Question about Toyota 4Runner

Open Question

Removal of 1990 4runner front fender

How to remove passenger front finder on 1990 toyota 4runner

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 173 Answers

SOURCE: replace front fenders 1999 wrangler

Hi! In your case you have to read this STEP by STEP instruction how to replace fenders


  1. First, raise the front of the car and rest it securely on jack stands.
  2. Remove the front wheels (the fender can be removed with the wheels on, but you'll have limited access to the fender bolts -- we recommend removing the wheels).
  3. If you're removing the left front fender on a 1968 through 1973 model, unplug the horn wires and remove the horn. Don't hang the horn by the wires.
  4. Remove the bumper and bumper brackets
  5. First remove the headlights and turn signal lights and wrap the wiring up out of the way.
  6. Remove the nut, washer and bolt that attach the fender to the running board.
  7. Remove the bolts and nuts that attach the fender to the body.
  8. Remove the fender, the beading, and the rubber spacer between the fender and the running board. Note: The rubber bead has cutouts around the bolt holes (it doesn't have holes in it - just cut outs).
  9. Inspect the rubber beading and the rubber spacer washer. If they are cracked, dried, or deteriorated, replace them.

  10. Check the threaded holes in the captive nuts in the body and clean them up with a tap if necessary. Lubricate the bolt threads.
~~~ Fender Replacement -
  1. Place the fender in position against the body without the beading and loosely install one bolt at the top to support the fender.
  2. Now start the rest of the bolts. Tighten them just enough to hold the fender in position.Install a new rubber spacer washer between the fender and the running board, then install the bolt, washer and nut that attach the fender to the running board, but don't tighten yet.
  3. Hold the new beading around the body immediately above the fender, and mark (with chalk) the locations of the bolts. Cut slots in the portion of the beading the extends down between the body and the fender to accomodate the bolts, then push the beading into place with your hand. Make sure the slots in the beading slip over the bolts. Be extremely careful about the fit of the beading as you gradually and evenly hand-tighten the fender bolts a few turns.
  4. Gradually and evenly tighten all the bolts.
  5. The remainder of installation is the reverse of removal. GOOD LUCK thanks

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: Remove right front fender on 2005 odyssey

NO 2 BOLTS ON TOP OF FENDER UNDER HOOD 1 BOLT BEHIND PLASTIC TRIM BY MIRROR PULL THIS PIECE BACK TOWARDS MIRROR OR IT WILL BREAK TABS OFF 1 BOLT UNDER ROCKER TRIM 1 SCREW INTO ROCKER AND 1 SCREW BEHIND PLASTIC SHROUD GOING INTO BUMPER FROM UNDER NEATH PULL BUMPER BACK SLIGHTY AND YOU WILL SEE A WHITE PLASTIC CLIP PULL BACK AND BEHIND THIS IS A BOLT REMOVE HEADLIGHT CLIP FROM FENDER AND LOSEN BOLT BY HINGE NOW FENDER SHOULD COME RIGHT OFF BOOK IS 2 HOURS TAKES 1 HOUR TO REMOVE BUT GOES ON IN ABOUT 30 NINUTES

Posted on Mar 21, 2009

  • 57 Answers

SOURCE: how do i remove a fender from my ford ranger 2008?

there should be bolts under the hood as well as screws by the wheel wells remove these and the fender should come off rather easily

Posted on May 02, 2009

  • 24 Answers

SOURCE: Remove left front fender 1967 Chevelle

There are quite a few bolts on this fender. One on the bottom of the rocker, one between the the door and fender on the "A" pillar, one on the cal, one on the firewall then several on the inner fender and several on the radiator core support. after these are removes you need to take ou the head light assembly and you should have a fender brace under the front of the car. Hope this helps.

Posted on Oct 07, 2009

  • 2 Answers

SOURCE: How do I remove a wrecked front fender assy/quarter panel?

The front fenders are connected to the A pillar above the the top hinge, at the bottom of the rocker panel seam, three bolts pass through the hood hinge support in the middle of the fender, four bolts on the radiator support, three vertical bolts on the top radiator brace, and one bolt at the rear of the wheelhouse to the cab body. Yes, the wheelhouse is spot welded to the fender and must be removed with it. Remove all the bolts listed as well as the bolts retaining the splash shield. The splash shield is a plastic liner connected to both the wheelhouse and the fender. Remove the headlight/cornering lamp assembly. The best way I have found to do this is to loosen the bumper to framebrackets and let the bumper assembly sag to gain clearance. If the upper bumper cover is removed to gain the clearance needed you will more than likely need to get a new cover as the nylon clips have a tendency to break during removal. Once the fender/wheelhouse assembly has been removed use a spot weld cutter to separate the wheelhouse from the old fender. Check the new fender for clearance and fit on the vehicle. Make all the needed adjustments to get the fender to fit correctly. Remove the fender and attach the wheelhouse. This should be done by spot welding. It can also be done using bolts. If using bolts place some 3M double stick weather strip adhesive tape in the seam to prevent direct contact of the parts to prevent rattles and squeaks. Drill the new fender to match the holes made by the spot weld cutter in the wheelhouse. Use stainless bolts and lock nuts so that the assembly can be services if needed. I would also recommend using Wurth Rust Inhibitor on all the seams to prevent rust and once cured it is an excellent adhesive and will reduce noise coming from moving body panels. Good Luck. It is not as bad as it sounds. Take your time and it will be worth the effort.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was in a front end finder binder on the passenger side now my car will not start


The battery is buried on that side there is a panel in the front of the fender well to remove for access Check for broken wire or other damage.

Oct 19, 2014 | 2004 Chrysler 300M

1 Answer

Passenger side front fender removal


study the new fender and where there is a bolt hole then that is where you will find the bolts to remove on the old fender . They will normally be along the top inside , at the bottom near the door and around the bumper and up the panel that the door hinges are attached to

Jul 20, 2014 | 1998 Buick LeSabre

2 Answers

How do you remove the front fender


Tool`s needed 3/8 drive socket set.
i`m assuming you want to remove the outer finder.
to remove fender locate the row of bolts along the inside after you open the hood under the splash Gard and the inner wheel well and a few in and around the grille maybe even in the door cavity .
Start at the bottom and work up saving the top row for last.
to install just reverse.
Good Luck and take your time

Jul 02, 2014 | 1993 Cadillac DeVille

1 Answer

How do you get acces to right fender on expedition to pound damage out?


you can take out the inter wheel well fender or guard I forgot what they call it. remove the tire and you can get to the bolts a lot easier. when you take out the inter fender you may be able to get to the dent from the fender wheel well. if not and you need to remove the fender you will find bolts under the hood along the top of the finder edge. there is one under the cow as well right close to where the fender connects to the suv by front door. you will also find bolts that hold it to the front bumper I believe. you might have to look around to see if there is more. I just replaced my fender on my 2003 expedition about a month ago. you can get them on line for about $75. also I just remembered there are like 3 bolts that you can get to right by the front door running down to the trim piece on the bottom of fender. good luck

May 27, 2014 | 2004 Ford Expedition

1 Answer

Where is the windshield washer motor of a 96 toyota camry located?


The washer pump is located at the bottom of the fluid tank. On a '96 or '97 it's on the right (passenger side) under the inner fender liner. Remove the Right front wheel. Remove the lower engine cover. You should be able to get the pump out. If it's corroded fast, then you'll have to remove the inner fender liner (lots of clips will break) and remove the entire tank assembly.

Apr 18, 2011 | 1997 Toyota Camry

1 Answer

1997 2.4 toyota cavlier where exactly on the car is the computer located?


It is inside the right front fender, just in front of the tire (passenger side). You will need to remove the forward wheel well skirt from the fender and front air dam to access. Providing its a Chevy Cavalier rather than the Toyota Cavalier which I'm not familiar with.

Mar 19, 2011 | 1998 Chevrolet Cavalier

1 Answer

Need to remove front passenger side quarter panel


It's called a front passenger fender and it is bolted on with common bolts. Regular ratchet and sockets will do the job for you.

Jan 14, 2011 | 1995 Toyota Tercel

1 Answer

Front fenders need to be removed


take the inner fender well out, unbolt the fender from the bumper, take the 2 bolts out under the car at the fender, lastly take all the bolts along the fender out, and gently pry it loose

Aug 07, 2009 | 2000 Toyota Celica

1 Answer

I am removing the right front fender on a 96 pontiac grand prix


U NEED TO TAKE YOUR FINDERWELL OUT FRIST ON THAT SIDE THIN OPEN HOOD THE BOLTS R RIGHT AT THE TOP WERE YOUR HOOD FITS THE FINDER SHOULD BEE ABOUT SIX OR SO NOTE THE FINDER WELL IS THE UNDER NEATH PART OF YOUR FENDER U MAY WONNA REMOVE YOUR PARKING LIGHT FOR THAT SIDE JUST TO MAKE SURE U DONT BRAKE IT AND JUST BELOW THE MARKER LIGHT SHOULD BEE A FENDER BRACE REMOVE IT ALSO ITS LIKE A SHORT METTEL BAR ALL BOLTS SHOULD BEE 1/2 INCH GOOD LUCK AND RATE THIS PLEASE

Apr 05, 2009 | 1995 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...