Question about Cars & Trucks

Open Question

Astrostart does not work after replacing car battery

I had to replace my Jeep Liberty's battery and now my astro start doesn't work

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2002 Jeep Liberty 3.7L air conditioner bearing replacement

did you check the recall items for this?

Posted on Jun 28, 2008

  • 142 Answers

SOURCE: airbag light stays on 2005 jeep liberty

It probably will cost a few bucks to get the code reset, but you don't need to go to the dealership, most shops with a good scanner equipped for air bag code reading will be able to diagnose and reset the light. The most probable reason for the code is the battery being dead for a while, there is a capacitor in the airbag circuit to make sure the airbag can go off in a collision even if the battery disconnects itself in the process. There is a slim chance it might be something else but either way the shop should be able to tell you what the problem is, and get it fixed... But, just for fun, before doing all this, i'd disconnect the battery for 30 minutes to an hour and reconnect it back, some systems do effectively reset themselves this way.

Posted on Jan 13, 2009

michigan man
  • 3533 Answers

SOURCE: how to replace rear brake pads on 2005 jeep liberty

put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Posted on Mar 01, 2009

  • 1 Answer

SOURCE: How to replace reak brake rotors on Jeep Liberty

Replace rear rotors on 04 liberty.
Remove tire & wheel
Remove brake caliper, tie up out of way.
Back off e-brake shoe adjustment.
Remove factory spring clip from lugs (2places)
This is the crude part....
After attempting to pull off disc/drum with puller....I got pretty sick of it. Understand this is in the Northeast with lots of salt on the roads in winter. Needless to say there is a ridge of rust around the inside edge of the e-brake surface. Any more pressure and I was afraid of damage to the e-brake shoe asembly. I then took a small grinder with a cut off wheel and cut the disc thru (used space where caliper usually sits). Also cut nearly through the face between 2 lugs. You can't quite get thru the back corner at the disc. Since the material is cast iron it will crack when you drive a wedge in the slot cut in the disc. This opens the housing around the shoes and it slides off easily. The cutting operation took less than10 mins, alot less than the puller with hammer assist!
I know this is a bit "unorthodox" to say the least, however the object is to remove the old junk disc safely and as quickly as possible, without harming the e-brake parts inside.
Install new parts in reverse order, new pads go in easy after squeezing the caliper piston back with a c clamp as is the normal procedure.

Posted on Mar 22, 2009

  • 110 Answers

SOURCE: 2006 jeep liberty cigarette lighter problem

its probably not the lighter itself, it's probably lost power. check the fuse for the cig lighter and see if blown. if it is, replace. if it blows immediately you have a dead short. if not, pay attention to when it stops working. could be a problem with whatever you are plugging in, or something else on the circuit

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Jeep Liberty


Possible solution - This happened to me and my battery was dead in my key fob and also I needed an ignition switch because a piece on it was broken which therefore wouldn't turn to start the engine.

Apr 26, 2013 | 2008 Jeep Liberty

1 Answer

I have a 2004 jeep liberty, what is EATX?


Try unhooking your battery. It should reset the light. If that doesn't work it could be the relay again. I have had that happen to me with my 2001 Expedition. Was told it was caused by me giving someone a jump and it caused the service engine soon come on.

Jun 10, 2012 | 2004 Jeep Liberty

1 Answer

Jeep Liberty 2004 sport gas cap not sealing


You can get the silicone grease at automotive and hardware stores. Apply to rubber seal on cap about every 2 to 3 months. This will ensure a seal so that the engine light doesn't come on. Worked great on My 2008 Liberty.

May 30, 2012 | 2004 Jeep Liberty

1 Answer

My 2006 Jeep Liberty won't start or turn over all I keep hearing is this click sound when I turn the ignition , Plus I just replaced the battery........What shall I check next?


check your starter,better yet has your alarm system been activated and possibly shut down your car a passive alarm will do that

Mar 27, 2012 | 2006 Jeep Liberty Limited

1 Answer

2007 jeep liberty suddenly won't start after


Try starting in neutral. Gear sensor may be heating up and not registering park.

Mar 03, 2012 | 2007 Jeep Liberty Sport

1 Answer

Jeep liberty 2005 with code p0700 and check engine blink 5 time


You need disconnect the battery, leave it off for about 10 min. see if that doesn't clear the codes.

Jul 13, 2011 | 2005 Jeep Liberty

4 Answers

2002 Jeep Liberty 2WD 377l v6 won't idle when first started up.


it doesn't have to do with the battery. I just had this same problem. Clean the carbon out of the IAC and test to see if this solves the problem. Should it not, the next step is to replace the Throttle Position Sensor. This is a common problem with this model of jeep. The can of cleaner and the sensor only cost 45 bucks, and about an hour total to do.

Aug 05, 2009 | 2003 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...