Question about Chevrolet Cars & Trucks

Open Question

How to program replacement RKE for 2011 impala

Rke programing

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: REMOTE KEYLESS ENTRY 99 GRAND CARAVAN

INSTALLATION: REMOVE THE TOP DASH COVER USING A FLAT TIP SCREW DRIVER AND LOCATE THE CONNECTOR FOR THE RKE MODULE. THE CONNECTOR WILL BE SMALL AND LOCATED NEXT TO THE HVAC DISTRIBUTION DUCT. MOUNT MODULE AND INSERT THE CONNECTOR. SINCE THE BODY CONTROL MODULE IS INVOLVED WITH THE RKE THIS MAY OR MAY NOT WORK BECAUSE NOT ALL CONTROLLERS ARE THE SAME BUT IF YOU WOULD LIKE TO TRY TO PERFORM THE TASK TRY THIS. FOR PROGRAMMING:

  1. Using a functional key fob transmitter, unlock the vehicle and disarm the Vehicle Theft Security System.
  2. Insert ignition key into the ignition switch.
  3. Turn the ignition switch to RUN position without starting engine.
  4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum four seconds (maximum ten seconds)
  5. While holding UNLOCK button, and before ten seconds passes, press and release the PANIC button. A single chime will sound to verify that the RKE module is set to receive the new Vehicle Access Code(s)
  6. Within 30 seconds of the chime, press and release the "LOCK" and "UNLOCK" buttons on the transmitter at the same time. Then press any one of the buttons. The BCM will sound an abbreviated chime to acknowledge that the programming of the transmitter has been completed and was successful.
  7. Repeat step 6 for all transmitters that will be used with this vehicle (up to 4 total)
  8. Programming mode will last for 30 seconds. To get out of programming mode sooner, turn the ignition OFF. A single chime will sound to verify that the RKE module will no longer accept additional Vehicle Access Code(s)
  9. When Vehicle Access Code(s) programming is complete, turn the ignition switch to the OFF position and verify RKE system operation using each key fob

Posted on Sep 27, 2008

Ad
  • 1 Answer

SOURCE: Need programming instructions for RKE for 2000 Mazda 626

2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Posted on Nov 13, 2008

picatudo
  • 239 Answers

SOURCE: interference to RKE, immobilizer activates, cannot disarm immobil

Car Alarms: 1998 Grand Cherokee RKE, rke system, jeep dealership
Good luck let me know !!

Posted on Jan 28, 2009

  • 10 Answers

SOURCE: 2004 ram remote keyless entry

The instructions are in the owner manual on how to manually program it.

Posted on Jul 07, 2009

  • 10865 Answers

SOURCE: what does rke battery low light mean

RKE means remote keyless entry. Install a new battery in your key fob and your light will go off. Regards, Joe
ps - kindly rate my answer as helpful. thank you.

Posted on Feb 17, 2010

Testimonial: "thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Ford 2010 Ford Explorer "Remote Keyless Entry (RKE) module" located


The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????
  • The doors do not lock/unlock using the remote keyless entry (RKE) transmitter
  • RKE transmitter battery
  • RKE transmitter
  • RKE transmitter programming
  • Aftermarket system
  • SJB
  • Go To Pinpoint Test H .

Apr 16, 2017 | Ford Cars & Trucks

Tip

Do it Yourself: Reprogramming the Remote Keyless Entry (RKE)


Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Jeep Grand Cherokee Alarm System (1993-1998)

I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module. If you wanna download this procedure, clic the image.

79482d7.gif

Enjoy Jeep.

on Sep 23, 2009 | 1993 Jeep Grand Cherokee

1 Answer

The RKE can lock/armed but can't unlock my chevy aveo. I used to insert my key to driver's door to unlock the car


The black contact points inside your RKE get dirty, and contaminated...you can try cleaning, but not a lasting fix...your local auto parts store sells replacement housings for RKE about $15. I would try putting the guts from your current RKE into a new case, as the new case contains new contacts...you must match the RKE exactly by model #...chances are this will work...if not then you will need to replace the RKE at about $70...AutoZone sells these replacements in my area...hope this helps

Aug 06, 2015 | Cars & Trucks

2 Answers

My Ford Focus car doesn't centrally lock anymore, I have to use the key. It's not the fob battery because I changed it.


Sure you did put in a new battery? sure you did insert it correct? not the other way around? sure you did use the correct battery? like CR23 or AAA?
Sure all contacts in the battery compartment and on the battery are clean and shiny?
just a few things you could check.

Feb 09, 2015 | Ford Focus Cars & Trucks

1 Answer

Remote keyless entry doesn't work


use a code reader to reset the CPU program as removing the battery from the system then restoring it some times corrupts the CPU program and creates problems rather than fixing them

Mar 02, 2014 | 2008 Saturn Astra

1 Answer

We own a 2000 Pontiac Grand AM, 3.4 liter, 2 door coupe with front wheel drive and recently replaced the transmission and now can't find our key set. Great start We hired a local Lock Smith who...


You can purchase new Remote Keyless Entry (RKE) transmitters from the dealer or you can order them online at the web sites listed below or several others. Your vehicle provides for programming the RKE transmitters without the use of a scan tool. Follow the instructions below.

2000 PONTIAC GRAND AM RKE TRANSMITTER PROGRAMMING

WITHOUT A SCAN TOOL

1. Close all vehicle doors. Remove key from ignition lock cylinder

NOTE: STEPS 2 AND 3 MUST BE COMPLETED WITHIN 25 SECONDS OF PRESSING THE DOOR UNLOCK SWITCH
2. Press and hold door UNLOCK switch. While holding UNLOCK switch, insert and remove the key in the ignition lock cylinder twice. Do not rotate the lock cylinder.
3. Insert the key a third time, leaving the key in the lock cylinder. Keep the lock cylinder in the LOCK position for the remainder of the procedure. Release the door UNLOCK switch. The chime will sound 3 times to signal that the programming/diagnostic mode is active.
4. Press and hold LOCK and UNLOCK at the same time on the RKE transmitter for approximately 4 seconds. The chime will sound 2 times signaling that the transmitter has been programmed.
5. Repeat step 4 for each transmitter being programmed. (You can program up to 4 transmitters.)

6. To exit program mode, turn the key to the RUN position then back to the LOCK position and remove the key. Your transmitters should now work to lock and unlock your doors.

2000 Pontiac Grand Am Transponder (direct links)

- autotransponder.com

-keylessremotes.com

-ikeyless.com

Jun 10, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

1997 jeep will not start thinking its the anti theft lock but dont not how to reset the code ... does anyone know how


I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module.
Click here also; http://www.scribd.com/doc/20110658/Keyless-Entry-System-Jeep-Grand-Cherokee

Oct 05, 2010 | 1997 Jeep Cherokee

1 Answer

I want the security feature to the remote disabled how do I do this?


To de-program the RKE fob from the 1st truck ( the 1998 one ? ), enter programming mode. I had to try 3 times on my 2001 to enter programming mode, and thought I did it the same each time, obviously I did not, so do not give up if you do not enter programming mode the 1st time.

Once you enter programming mode ( locks cycle ) wait 30 seconds, and programming mode should exit. Entering programming mode for the RKE fobs erases all previous RKE fobs.

This should cure the problem with the RKE fobs being programmed to 2 different trucks.

The RKE ( Remote Keyfob Entry ) is not a security feature, just a convenience item, so you are not disabling any actual security item.
642a92c.jpg

Oct 06, 2009 | 1998 Ford F150 Regular Cab

1 Answer

REMOTE KEYLESS ENTRY 99 GRAND CARAVAN


INSTALLATION: REMOVE THE TOP DASH COVER USING A FLAT TIP SCREW DRIVER AND LOCATE THE CONNECTOR FOR THE RKE MODULE. THE CONNECTOR WILL BE SMALL AND LOCATED NEXT TO THE HVAC DISTRIBUTION DUCT. MOUNT MODULE AND INSERT THE CONNECTOR. SINCE THE BODY CONTROL MODULE IS INVOLVED WITH THE RKE THIS MAY OR MAY NOT WORK BECAUSE NOT ALL CONTROLLERS ARE THE SAME BUT IF YOU WOULD LIKE TO TRY TO PERFORM THE TASK TRY THIS. FOR PROGRAMMING:
  1. Using a functional key fob transmitter, unlock the vehicle and disarm the Vehicle Theft Security System.
  2. Insert ignition key into the ignition switch.
  3. Turn the ignition switch to RUN position without starting engine.
  4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum four seconds (maximum ten seconds)
  5. While holding UNLOCK button, and before ten seconds passes, press and release the PANIC button. A single chime will sound to verify that the RKE module is set to receive the new Vehicle Access Code(s)
  6. Within 30 seconds of the chime, press and release the "LOCK" and "UNLOCK" buttons on the transmitter at the same time. Then press any one of the buttons. The BCM will sound an abbreviated chime to acknowledge that the programming of the transmitter has been completed and was successful.
  7. Repeat step 6 for all transmitters that will be used with this vehicle (up to 4 total)
  8. Programming mode will last for 30 seconds. To get out of programming mode sooner, turn the ignition OFF. A single chime will sound to verify that the RKE module will no longer accept additional Vehicle Access Code(s)
  9. When Vehicle Access Code(s) programming is complete, turn the ignition switch to the OFF position and verify RKE system operation using each key fob

Sep 26, 2008 | 2000 Dodge Grand Caravan

1 Answer

Programming keyless remote for Neon 2004


There is a way to program a remote if there is already a valid remote. Unfortunatly if you don't have a valid remote the only way to get one programmed is at the dealership with their scan tool.

I have pasted directions for programming a remote if there is already a valid transmiter.


CUSTOMER PROGRAMMING For a customer to be able to program RKE transmitters themselves, at least one RKE transmitter must be programmed already. This procedure is to add additional transmitters. If all transmitters are lost, the DRB III® scan tool must be used to program the new transmitters.
  1. Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop).
  2. Using the RKE transmitter programmed to the RKE module, press and continuously hold down the UNLOCK button for 4-10 seconds.
  3. Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module.
  4. A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes).
  5. Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred.
  6. After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.

Jul 30, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...