Question about Cars & Trucks

Open Question

Have a case 850K dozer Parking brake wont release and wont drive . Have a code number 4531 coming up. Any sugestions?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 566 Answers

SOURCE: 03 Yukon denali park brake warning wont turn off

hi for info the brakes warning light on dash is also an indication that brake fluid level is low? or there may be a leak resulting in fluid level drop ? also considering age of car you may need to inspect brake pads wear ? if your car has low brake pads wear indicators attached to pads ? or the hand brake switch req's checking to ensure it is being pushed to off position when h/brak is down ? so fluid level low is the obviouse 1st check as fluid will displace from reservoir as pads wear low hence the level indicator on fill cap trips on may i suggest if it is low level b4 you top up? check your b/pads if you have not done so recently? or replaced since new ? hope this helps you locate problem best wishes from the uk

Posted on Jan 03, 2009

  • 45 Answers

SOURCE: PARKING BRAKE RELEASE

IF U SET DOWN ON THE ROCKER PANEL ON THE DRIVERS SIDE AND WITH YOUR RIGHT HAND REACH RIGHT UP TO THE RIGHT SIDE OF THE PARKING BRAKE ASSEMBLY, THEIR IS A LEVER U CAN FEEL (ITS GOT LIKE A LITTLE HANDEL TO THIS LEVER) AND I BELIEVE U PULL IT TO U, THIS IS THEIR INTENTIONAL TO RELEASE THE BRAKE, I HAVE A 97 AND I HIT THE PEDAL WITH MY FOOT SOMETIMES AND THE LIGHT WILL COME ON SO I HAVE TO RESET IT THIS WAY, I THINK TO MUCH FORCE OR OUT OF ADJUSTED BRAKE CABLE WILL CAUSE ALSO. GOOD LUCY TO U..

Posted on Mar 05, 2009

  • 1 Answer

SOURCE: Parking Brake Alarm

inset the key and switch on to position 2
Scroll through the warning display untill you get the service indicator apears
Press and hold the reset button on the left of the dash apnel for about 4 mins
You will be asked if you want to reset
Press anh hold the reset button again until you hear an audible warning
It should now show the new interval to a service

Posted on Apr 06, 2009

  • 7 Answers

SOURCE: Merecedes C270 - the foot operated parking brake,

Hi :)
Very common problem do loads. You need to lubricate the handbrake linkage under the rear seats ( the bit ur bum goes on). If you have a estate car then the seats will flip up but if its a saloon car then you will have to remove 2 13mm nuts for either side seat. When ur under there, u will see a little black panel in the middle, remove it 2 8mm self tappers and a 13mm nut. right you should now see the linkage where the cable splits to either side of the car. Get a load of wd-40 and spray whilst some else operates the handbrake 100 times or so. sorted! Dont forget to adjust the handbrake at the wheels after, go all the way with the adjust and back off two clicks either side.
Hope this works and good luck1
Carlo@ss

Posted on May 18, 2009

greg_margo
  • 1959 Answers

SOURCE: parking brake release

There should be a manual release. Reach up along the parking brake pedal. Ford has a manual lever that you pull toward yourself to release the parking brake. Hope this helps our with your problem. Best of luck.
Greg

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How too release the emergency brake foot pedal when the cable is broken?


About 73,400 results (0.87 seconds) Search Results

    Parking brake release cable snaps - Chevy Avalanche Fan Club of ...

    chevyavalanchefanclub.com > ... > Problems: Brakes

    24 posts - ‎16 authors
    Went to release the parking brake on my 04 and the cable snapped. ... More like the end cap coming of the cable that attaches to the foot pedal. ..... Then I released the parking brake, pulled out the broken release cable/handle assembly, ...

    How To Install Repair Replace Parking Brake Release ...

    ? 5:54
    https://www.youtube.com/watch?v=qx0oGfV62NQ
    Jun 23, 2011 - Uploaded by 1A Auto Parts
    How To Install Repair Replace Parking Brake Release CableHandle ... or replace a broken or worn out parking brake release cable handle.

    Emergency Brake Pedal Assembly & Stuck Brake Cable ...

    ? 10:13
    https://www.youtube.com/watch?v=0jYfvthBzhU
    Apr 17, 2014 - Uploaded by corgLLC
    Emergency (Parking) Brake Pedal Assembly & Stuck Emergency (Parking) Rear Brake Cable The emergency ...

    E-Brake Cable Broken? Stuck Emergency Brake... Help Please ' Chevy ...

    www.tahoeyukonforum.com > ... > Engine & Drivetrain


Jan 25, 2016 | Cars & Trucks

1 Answer

Parking brake stuck


where the cables connect to the rear parking brake shoes is like a hook shape waht iv seen happen is thay rust and stick after being aplied only real fix is to remove and free them up and re assemble the parking brake taking the cables off wont release the shoes from teh drum and will cause more damage in more parts will be needed to compleat the repair

Feb 28, 2014 | Dodge Dakota Cars & Trucks

1 Answer

2011 Can Am Spyder SE5, parking brake will not release. Parking brake light flashing on dash panel and, will not release rear brake.


answering the question on 2011 Can Am Spyder SE5, parking brake will notYou will find the foot brake is released ok but the error still flashes. This is an issue with the brake pressure switch that needs to be reset. log into the bikes computer to access the error codes and verify the error first and take down the error number then look into the service manual which will tell you how resolve this electronic fault.

Oct 10, 2011 | Cars & Trucks

1 Answer

Brake light in dashboard coming on when driving


I am assuming that you are talking about the RED brake warning lamp and not a YELLOW Anti-lock Brake Warning lamp. If this is not correct, please let me know. There are several things that can cause this. The parking brake my not be released properly. The switch for the parking brake may be defective. Your brake fluid level could be low. (If it is, it is EXTREMELY IMPORTANT that you find out WHY!) Or you could have a brake system hydraulic failure.

In any case, it is NOT SAFE to drive the vehicle until the CAUSE has been determined. It may be safe to operate the vehicle temporarily if you find it is being caused by a defective parking brake switch, but any of the other possible causes make the vehicle DANGEROUS to drive.

May 15, 2011 | Toyota Corolla Cars & Trucks

1 Answer

The parking brake is disengaged and when i am driving it will flash


In most cases when the brake or parking light comes on it's due to the switch not making full contact with the parking brake linkage. Sometimes just manually pulling the brake back will make the light go off. Fix is to adjust the switch out just a little so that the switch goes off when the brake is released.

Jul 05, 2010 | Cars & Trucks

3 Answers

Right rear brake appears to be locked


Your rear brakes are not releasing. Make sure your brakes are fully released. Pull up and down on it a couple of times.Jack up the rear of the vehicle to get the tires of the surface and see if you can turn the wheels by hand. Brake cable may be bad. do this and post again

Dec 11, 2009 | 1992 Honda Civic

1 Answer

2004 Accord will not move on cold mornings


When you release the parking brake, the handle goes down, but the cable in the casing is probably not moving. When you drive away, your parking brake is still set. The movement of the wheels against the brake shoes (or discs) produces heat pretty quickly and causes the brakes to release (at least enough so that there is no longer any contact between the brake shoe or disc and the brake drum or rotor).
The casing normally runs from the back of each hub to a point somewhere forward where they come close together so the brake handle can pull both brake cables at once. The casings could be lubbed, but that is something you probably want a garage to try to do (pretty messy, spraying lub into a casing with the cable is in it, and not a guaranteed solution unless both cables are disconnected, removing from the casings, and cleaned).
Probably the best thing to do to solve the problem in the short run is NOT to set the parking brake in very cold weather.
Hope this is helpful.

Dec 11, 2009 | 2004 Honda Accord

1 Answer

Parking brake assembly diagramneeded


90b25b6.gif
Item Part Number Description 1 2553 Rear Disc Brake Caliper 2 4234 LH Axle Shaft 3 2C026 Rear Disc Brake Rotor 4 383609-S Push Nut (2 Req'd each side) 5 2C189 Rear Brake Anti-Lock Sensor Indicator 6A 3912205-56 Nut (4 Req'd) 7 2C220 Rear Wheel Disc Brake Adapter 8 1177 Inner Wheel Bearing Oil Seal 9 390317-S190 Bolt (4 Req'd) 10 1225 Rear Wheel Bearing 11B 2B296 Disc Brake Caliper Locating Pin A Tighten to 27-54 Nm (20-40 Lb-Ft) B Tighten to 26-35 Nm (19-26 Lb-Ft)
The automatic (vacuum) release-type is standard equipment on all vehicles. The automatic vacuum-type parking brake system contains the following features:
  • A parking brake release control motor (2A843) with mounting bracket bolted to the parking brake control .
  • The vacuum-actuated diaphragm within the parking brake release control motor which is connected by a rod to the upper end of the parking brake release vacuum hose (2B653) .
  • The parking brake release vacuum hose which connects the parking brake release control motor to the engine manifold through a vacuum release switch at the steering column tube (3514) .
  • The parking brake release control motor which is actuated to release the parking brake whenever the engine is running and the transmission is in a forward-driving gear.
  • The automatic parking brake control which has a manual release feature that releases the foot parking brake control by applying force to the parking brake control pedal in the "apply" direction to the point of initial application.
  • The parking brake control will return to the full-release position after removing the force.

Apr 14, 2009 | 1994 Lincoln Town Car

1 Answer

ABS Light and Parking brake light on


check your fuses, then check the ABS valve located beside the master cylinder and the wiring to it and finally check your speed sensor, which is located on the transmission on a 2 wheel drive and on the transfer case on a 4 wheel drive. but make sure hat your E-brake is released as it will cause these lites to come on.

Oct 09, 2008 | 2000 Chevrolet S-10

2 Answers

Rear brakes


you probably have the parking brake set, in which case the drum cannot be removed. release the parking brake

Sep 13, 2008 | 1999 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...