Question about 2002 Toyota Camry

Open Question

2002 camry jack stand points - 2002 Toyota Camry

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2002 Answers

SOURCE: Jacking point for 1990 Toy Camry center of front.

Jack one side at a time. Place your jack under the lower control arm, or if it won't go under on a frame rail and lift from there. You may need to use some blocking to get the car high enough if you jack at a frame rail.
Jacking on the transaxle housing puts you at high risk of doing some very expensive damage. That housing is either aluminum or white metal. They don't bend like steel, they just break. Hope this helps.

Posted on Aug 17, 2009

Testimonial: "Thanks, I just thought I could do them both with the floor jack and jack stands. Best to do one at a time... "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A womp womp womp noise in the rear, tires are good, brakes look good, wheels are not warped, just had them balanced?


Go to a place that has a good smooth parking lot and a wooden private fence. Open all your windows and drive the car slowly as close as possible along the fence in order to pin point where the sound is coming from. The sound will echo back from the fence and will make it easier to pin point the area where the womp womp sound is coming from. Next thing you can do is lift the car up and place it on four jack stands in case you have a front wheel drive. If you have a front wheel drive and your car is on four jack stands, place you gear in nuetral and spin each rear tire separately to see which one is making the noise. Keep in mind that it might be a wheel bearing or if it a rear wheel drive and on four jack stands have someone drive it slowly while you listen for the noise. Some rear wheel drive differentials can make this noise if it is low on differial oil. Be very careful that the jack stands are on solid and making good contact with the car frame and flat on the pavement. Don't place yourself where the car can fall and hit you or run in to you. Good luck.

Dec 03, 2012 | 2002 Porsche Boxster

1 Answer

My 2002 camry keeps stalling at red lights


Clean also the IAC (idle air control) or replace it3_30_2012_4_41_00_am.jpg

Mar 29, 2012 | 2002 Toyota Camry

2 Answers

Need to take out tranny how big a job is it


unless you have lift to access the bottom of the car, and a transmission jack,dont attempt it.

Dec 21, 2010 | 1991 Toyota Camry

1 Answer

What tools do you need to replace rear brakes on a 1989 camry


The tools are jack, jack stands, impact wrench, or lug nut tools, sockets, piston compressor, lube, etc. But more important it the training, these are brakes and your life depends on it being perfect.

Sep 25, 2010 | 1989 Toyota Camry

1 Answer

Replace starter on 2002 toyota camry


Jack up car remove 2 or 3 bolts, undo 3 wires and it comes right out.

May 09, 2010 | 2002 Toyota Camry

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

2 Answers

Jacking point for 1990 Toy Camry center of front.


Probably best to do one side at a time, there is a frame underneath the passenger and drivers sides that you can jack up on, or you can jack up on the pinchweld located behind the tires, though probably best to go on the frame.
Then use jackstands, and should work good. or can just do one side at a time.

Aug 17, 2009 | 1990 Toyota Camry

1 Answer

Just need to replace the rear suspension springs. I have a replacement set, but need to know if I can do myself easily- or do I need special tools/equipment.?


u can do it yourself if u have some experience, u will need jack stands and floor jack heavy breaker bar and tape measure. u jack truck up until tires in the air support frame with jack stands and then jack axle loosen blolts and lift axle up/ down til u can pull bolys out put in new spring retighten measure both sides to common point to make sure axle is staright then do other side when done remeasure adjust if needed

Jul 06, 2009 | 2002 Chevrolet Tahoe

1 Answer

2004 tiburon : front jacking points?


The official front jacking points are on the reinforced edge of the unit body, just behind the front wheels.

If you're using a hydraulic jack, you can jack the front of the car from the front tow hook, place your axle stands under the front jack points, then let the car down onto the axle stands.

Always use axle stands when working on your car, never trust the jack alone.

Jul 05, 2009 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...