Question about 2004 Chrysler PT Cruiser
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
This is the pressure light, nothing to do with the oil needing to be being changed, you have low oil pressure being indicated, this will destroy the engine if the light is really indicating low oil pressure, have the oil pressure tested with a mechanical test guage at a shop, if the oil pressure is ok then replace the oil pressure light sending unit.
Posted on Nov 23, 2008
You may sneak it out with small fingers with out pulling out the starter.
If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.
Please rate this a fixya
Posted on Feb 08, 2009
Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.
* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.
Posted on Apr 30, 2009
remove the plastic cover.
remove the thing on top of the plug.
use a spark plug socket,(5/8) and replace the plugs with platinum plugs
Posted on Aug 19, 2009
P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor
intermittent crankshaft sensor
PCM detects an error when the camshaft position is out of phase with the crankshaft position
Posted on Sep 27, 2009
Tips for a great answer:
Mar 07, 2015 | 2004 Chrysler PT Cruiser
Sep 15, 2014 | 2004 Chrysler PT Cruiser
Apr 06, 2014 | 2004 Mercury Mountaineer
Sep 25, 2013 | 1996 Mercury Mystique
Jul 11, 2009 | 2004 Mercury Mountaineer
Jun 03, 2009 | 2005 Chrysler PT Cruiser
Feb 01, 2009 | 2004 Chrysler PT Cruiser
Nov 05, 2008 | 2004 Chrysler PT Cruiser
Jul 30, 2008 | 2004 Chrysler PT Cruiser
52 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: