Question about 2006 Mazda 3

Open Question

Dsc switch not working on my mazda 3 ts2 and the traction control light isstaying on?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: dsc

abs dsc module with a cost of £1700 from mazda...thats what fixes it..

Posted on Jan 11, 2009

Ad
  • 1 Answer

SOURCE: ABS, Traction control and handbrake

I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on but speedometer was not functioning and the ABS light was on. The rear ABS senssor was the problem.
SDM

Posted on Jan 23, 2009

  • 176 Answers

SOURCE: brake sensor? something else?

You have a faulty wheel speed sensor. This is a magnetic pick up sensor on your wheel bearing hub and it controls your abs. If the car can not sense all 4 wheels then the abs will default back to normal brakes and your traction control will not work. Look at your wheel bearing hubs and check for these sensors. They are on the underside of the car and are black plastic with a wire comming out of it. A piece of gravel may have broken the pick up or the wires to a sensor may be broken as well. To replace it is usually a couple of screws on the hub assembly and a plug to disconnect from your wire harness.

Posted on May 27, 2009

emissionwiz
  • 76846 Answers

SOURCE: How do i reset my abs and traction control lights

THESE LIGHTS RESET AUTOMATICALLY WHEN THE SYSTEM IS REPAIRED, AS LONG AS THERE IS A FAULT IN THE SYSTEM THE LIGHTS WILL REMAIN LIGHTED

Posted on Nov 04, 2009

  • 3911 Answers

SOURCE: my son haf a mazda and has turned the traction

you or your son should review the owners manual in the glove box. if it is not there then a replacement
can be had very cheap on ebay. it will come in handy again and again for all types of questions. a dealer is also a good source for this type of info.

Posted on Nov 27, 2010

Testimonial: "thanks very much he has no handbook but i will phone the dealer"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way of removing the light behind the traction control button of Masda TS2. Car is working fine and only paid £2000 for car so £1700 to fix problem is uneconomical.


yes theres a way, "i think your annoyed with the light flashing" , you can either pull the button switch and at the back of it cut the wire, and retape the exposed wire using electrical tape, and your done.

Nov 23, 2014 | Cars & Trucks

1 Answer

RX-8 & DSC


Hi Melissa,

I had a similar problem with my 2005 RX8 but didn't try using the DSC button. I had to have my engine rebuilt....I'm in So Cal and found a great private mechanic, are you local???

May 14, 2014 | 2005 Mazda RX-8

1 Answer

Mazdaspeed 3 08 Traction control light on


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS, TPMS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Anti-lock brake system. TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module. TPMS Tire Pressure Monitor System

Nov 01, 2012 | Cars & Trucks

1 Answer

How do i fix my 1996 mazda millenia traction control


IF YOU SEE TRACTION CONTROL LIGHT YOU NEED TO LET A GARAGE OR DEALERSHIP CODE SCAN ABS BRAKE SYSTEM AND TRACTION CONTROL SYSTEM TO SEE WHAT CAUSING TRACTION CONTROL LIGHT FLASH COULD BE BAD WHEEL SPEED SENSOR BUT GET VECHICLE CODE SCAN.

Jul 07, 2011 | 1996 Mazda Millenia

1 Answer

I am running a mazda 6 TS2 2004 model. 2 amber lights came on my dashboard this morning. One of a car skidding and the other of an engine.


these are traction control and service engine. first look for a button or switch for the traction then have an obd2 scan done. you can scan it first this may tell you about the traction. your local auto zone or advance auto does this service for free if you don't have access yourself.

Jan 17, 2011 | Mazda MAZDA6 Cars & Trucks

1 Answer

How to switch traction control off on a 2002 bmw 320d


When is ASC button - press to off traction , end warning control of traction lighting.
When is DSC button - pres and hold 5seconds. warning control of traction lighting.

Mar 22, 2010 | 2002 BMW 3 Series

2 Answers

How do i shut off the traction control in my 2001 BMW 3-series coupe when there is no switch on the dash?


To turn off the traction control, you need to press and hold the traction control button. Normally this is located on the centre console above the gearstick and you should have one of the following;

ASC or ASC +T
DSC
finally a button with an exclamation inside a triangle with an arrow on the outside in a clockwise direction. You'll have one of these 4 buttons.

Simply pressing it once will partially turn it off - (depending if its dsc, if not dsc but asc then the system will be turned off)

If you press and hold however, the system will be fully turned off and a warning light will appear on the dash. Again this all depends on the system you have and if you need to press and hold until the light comes on the instrument cluster,or just to press once!

Hope this helps!

May 05, 2009 | 2001 BMW 3 Series

1 Answer

Dsc


abs dsc module with a cost of £1700 from mazda...thats what fixes it..

Oct 14, 2008 | 2006 Mazda 3

Not finding what you are looking for?
2006 Mazda 3 Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...