Question about 1999 Chevrolet Venture

Open Question

Were is ignition control module location on 1997 chevy venture

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: location of venture speed control sensor

Mounted on transmission. replacement part # su1289 about $15 clearpixel.gif

Posted on Nov 22, 2008

  • 1 Answer

SOURCE: 1997 chevy astro van

The control module is located just behind the ignition coil. Sorta hard to get to but we got it and the van is running great.

Posted on Dec 22, 2008

TittyMonster
  • 13 Answers

SOURCE: Location of BCM

some chatrooms say its in the right side kick panel under the fuse box, I never looked for it myself, hope you find it

Posted on Feb 08, 2009

  • 462 Answers

SOURCE: 1997 Chevy Venture fuel pump replacement

UNFORTUNATELY YES

Posted on Jul 14, 2009

Danniboi
  • 1098 Answers

SOURCE: 1999 Chevy Express 1500 cranks over but will not

Hi

Have you checked the EGR valve, and or the air flow sensor? both could cause it not to start!

Also ensure the earth battery lead has a good connection to the car body from the battery.

Please get back to me if your unsure about these parts.

Regards
Dan

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the body control module located on a chevy venture 2000?


Remove glove box module is under glove box right side

Feb 12, 2015 | 2000 Chevrolet Venture

1 Answer

Show picture of ignition control module on 1999 chevy venture


The ignition module is under the coils. I assume you have a 3.1L engine, or a 3.4L. In any case, the coils are mounted onto the ignition module.

Apr 13, 2014 | 1999 Chevrolet Venture

1 Answer

Ignition control module location on 1997 dodge ram 1500 5.9


The ignition and timing are controlled by the PCM computer.

Aug 22, 2012 | Cars & Trucks

1 Answer

Where is my ignition module on my 99 chevy venture? How do I know if it is bad?


The ignition module is located right below the coil packs toward the back of the engine. The coil packs are bolted to it. Many auto parts can test these for once they have been removed.

Jun 03, 2010 | 1999 Chevrolet Venture

1 Answer

Control module


Which control module? Ignition control? Engine control? What engine?

Apr 03, 2010 | 1997 Chevrolet K1500

1 Answer

Where is the purge solenoid on the 2004 chevy venture under the hood or on by the gas tank? thx


purge solenoid is located on top right side of engine, below ignition control module

vent solenoid is located Below center of vehicle, in front of fuel tank

Mar 03, 2010 | 2004 Chevrolet Venture Passanger

1 Answer

1007 chevy venture 3.4 liter v6 ''no spark''


These motors were notorious for the ignition module to go bad, if its not even trying to fire this very well could be the problem.first check the individual coils for spark. this motor has 3 coil packs,its not likely that all 3 would go bad at the same time. The ignition module is located behind these coils,which are held in place by 2 bolts each.remove the coils,then the bolts for the ignition module will be visible. remove the bolts, be careful removig the module,the crank sensor may be attached to the back of this module. The crank sensor is inserted straight into the block,held in by a rubber O ring, it will come out with the module so be sure to pull straight out on the module as to not damage the sensor.Take the module to your local parts store and have it tested, most places will do this for free.It will be a pass or fail test.If the module is good, your crank sensor may be bad, I've also seen this problem with this motor. good luck. Dale

Feb 14, 2010 | 1997 Chevrolet Venture

1 Answer

I have a 1997 Chevy ventura van... Where is the


all you gotta do is follow the top radiator hose to motor,it;s where the hose meets the motor.

Dec 30, 2009 | 1997 Chevrolet Venture

1 Answer

Wipers will not work on low spped or intermittant


check out autozone.com. You have to register for a membership (free) but then you will be able to use any of their vehicle repair guides. I had a similar problem with a 1996 Jimmy that ended up being the wiper control module (~$30). The module is housed with the wiper motor, under a plastic cover. The motor should be located, under the hood, on the firewall, very near to one of the wiper arms. Simply, unplug the wiring harness to the motor and remove the 3 or 4 screws that hold the cover on and pull the circuit board straight out and replace it.

Nov 16, 2009 | 1997 Chevrolet Venture

1 Answer

1997 chevy astro van


The control module is located just behind the ignition coil. Sorta hard to get to but we got it and the van is running great.

Dec 21, 2008 | 1997 Chevrolet Astro

Not finding what you are looking for?
1999 Chevrolet Venture Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...