Question about Hyundai i40

Open Question

Hyundai i40 gets stuck in reverse gear (manual)

Occasional event - reverse off drive lift gear lock ring to take out of reverse. The ring lifts but car will not come out of gear. After sometimes many attempts it just works fine and comes out of gear as if nothing has happened. Just not good blocking roads while you try and release it ..

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Car wont start - sometimes

try to check you starter motor&connection wiring from gearbox if auto

Posted on Dec 10, 2008

Ad
bunnydawg
  • 5158 Answers

SOURCE: Auto gear lever gets stuck in Park

Brian... i would respectfully advise you that the other site that bocon has given you is a scam.

I'm not sure if you are driving in winter conditons.... but first replace the interlock relay and see if that corrects the problem... and it should. it is indeed the interlock solenoid that will need to be replaced.

Robert

Please rate this solution

Posted on Jan 24, 2009

  • 16 Answers

SOURCE: rear lift gate will not go up or down with the

check inhibit switchs with scan tool,codes etc....possible faulty PLG latch,,(power liftgate latch)

Posted on Sep 01, 2009

wireguy212
  • 1627 Answers

SOURCE: the rear lift gate is stuck in the locked position

You will have to remove the panel covering the latch from the inside.Unhook it and you should be able to open it by prying up on it with a screwdriver.[Do these trucks not come with a rear hatch key?Don't know,just asking]

Posted on Nov 07, 2009

  • 1024 Answers

SOURCE: Shift lock release worked...do I still need to take car in?

I think the shift inter-lock solenoid was stuck at the time. it can also be your brake switch did not make contact. next time check your brake lights to see if they work while it hapen. so just wait!

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for reverse light switch location on 2012 hyundai i40 tourer


If it is a manual transmission it is screwed into the side of the transmission, if it is an automatic it is integrated into the range selector switch.

Jun 22, 2017 | Hyundai Cars & Trucks

1 Answer

Toyota sienna 2001 won't go in reverse but it goes forward


Does it crunch? If you lift the clutch and then press it down whilst trying to get it into reverse as this lets the cogs move allowing you to slip the drive into the gears this may allow you to get it into reverse. So here's the steps:
1 start the the engine
2 drive the car for about 10 kms
3 try and get the vehicle into reverse
4 lift the clutch whilst holding the stick in the gate ( you should feel the cogs turning and shaking the stick)
5 then push the clutch down again
6 if it still won't go repeat step 4/5
if it still won't work then try and get it into reverse whilst stationary and then start the engine it will jolt but can free up the gears!

hope this helps :)

May 15, 2014 | Cars & Trucks

1 Answer

Reverse cable disconnected fron manual gear shift


Hi, Unless you really know what your doing in gears best take it to garage should not be an expensive fix, just the gear box fork is not catching correctly. Hope this helps give me feedback please. Thanks, Malcolm Campbell.

Sep 04, 2017 | 2010 Ford Focus 1.8

1 Answer

2002 Auto Hyundai Accent stuck in second gear will not go up


having the transmission rebuilt in 2010 means that the tranny is 7 years old since service so there can be any amount of faults
run the fault codes to check for problem TCM, VSS, servos and solenoids
check the vacuum actuator for the transmission and vacuum lines
change the transmission oil
the engine light also reports on transmission failures

Jun 17, 2017 | 2002 Hyundai Accent

1 Answer

2009 Hyundai accent jerks when I put it in reverse or drive sometimes. What could be the problem


If I'm correct when you say **** your referring to a clunk or lift felt when you put in gear. This would most likely be either a broken transmission or motor mount.

Sep 09, 2012 | Cars & Trucks

1 Answer

2001 Hyundai Tiburon will not go in reverse, but drives fine otherwise.


Hi There,

As demonstrated in the test drive of the vehicle, the Tiburons gearstick has a little groove just passed the crown. Starting in nuetral - lift groove up and put it into the reverse position (where gear 6 is normally) by doing this lift you take the gear box to a second level. to move out of reverse simply take the gearstick and return it to nuetral then into first gear, you are now able to drive forward.

Hope this helps,

Cheers Buckaroo,
Chris.

Jul 10, 2010 | 2001 Hyundai Tiburon

2 Answers

If you have a motor mount going bad, are you suppose to be able to hear a noise of some kind?


Not usually. when a mount is bad, you can FELL the car **** when accell of a stop or changing from Drive to reverse. To check it, put on your parking brake, now hold the brake pedal with your left foot, now put the car in reverse, and press the gas slightly, the engine will move slightly, now put it in drive, the engine should shift slightly, if it moves a LOT like a few inches or moves upward, you may have a mount bad and it needs to be inspected.

May 12, 2010 | Hyundai Motor 2004 Sonata

1 Answer

I have a problem with the reserve on my car sometimes it works and sometimes it doesn't when I can't get reserve first and second gear is in reverse position on Volskwagen Passet 1994


pardo me for asking but is there not a method of selection of rverse gear by either pressing or lifting the gear lever so it will move over further so as to select reverse? or a lift up circular boss on gear lever itself that has to be lifted then reverse position can be selected ? hope this helps ?

Dec 19, 2009 | 1997 Volkswagen Passat

2 Answers

95 saab 900 2.3 Ltr 5spd trans stuck in reverse.


have you checked the shift coupler, you can see it if you look down at rear of engine on trans side. Mabey get someone to mave shifter around while you examin its operation

Aug 10, 2009 | 1995 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...