Question about 2001 Ford Ranger Regular Cab

Open Question

Location of crankshaft sensor on a 2001 ford ranger 4.0 motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

emissionwiz
  • 75822 Answers

SOURCE: looking for location of crankshaft sensor on a 96 ford f150 5.0

YOUR ENGINE USES A DISTRIBUTOR STATOR TO SENSE CRANK POSITION, IT IS INSIDE THE DISTRIBUTOR, MAKE SURE U REPLACE THE TFI IGNITION MODULE WHILE U ARE IN THERE, USE ONLY FORD PARTS, THE AFTERMARKET FAIL VERY QUICKLY AND CAN CAUSE REALLY WEIRD PROBLEMS. SEE PHOTO
6b11d79.jpg

Posted on Mar 19, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on a 1996 ford ranger 4cyl 2.3 ? Thanks Bob


is located at lower right front of the engine. down of the timing belt area. to remove this sensor you have to remove serpentine belt, the alternator. the lower radiator hose, the heater hose, and the water inlet when you remove the water inlet (two bolts) you are going to see the crankshaft sensor. remove the connector, the bolt, and pry it out. when you install the crankshaft sensor don't tight more of 7 foot pounds .

Jan 21, 2017 | Ford Ranger Cars & Trucks

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

1 Answer

What are the top most common causes for the injectors on a 2001 ford ranger to not fire/mis-fire


1. Fuel (ethanol) clogging
2. Sensor (crankshaft or camshaft) mis-communication...bad sensor or signal to computer
3. Electrical harness (age cracking, corrosion)
4. Fuel filter clogged, not sending proper fuel pressure
5. Fuel pressure too low (fuel pump)

Not necessarily in order...but start with fuel, move to electrical inspection, then sensor...unless you have a CEL code to start with first.

Apr 08, 2015 | 2001 Ford Ranger

1 Answer

Where are the freeze plugs located on 2001 ford ranger?


they are on the motor block on the pass side they are 2 inch round and should be 4 of them

Feb 06, 2011 | 2001 Ford Ranger Regular Cab

1 Answer

Where is the cam shaft sensor located on a 1990 ford ranger


YOUR TRUCK HAS A CRANKSHAFT SENSOR LOCATED BEHIND CRANKSHAFT PULLEY.

Jan 16, 2011 | Ford Ranger Cars & Trucks

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Locate


What engine? 3.0 has a crankshaft position sensor on the front of the engine just above the crank, and a distributor timing sensor on the top/rear of the motor.

Jun 11, 2008 | 2000 Ford Ranger SuperCab

1 Answer

2001 ford ranger


this truck has a swich under the gloves comparament it cutoff fuel pump power if the swich is on the off position.
if it crank but no spark or no fuel or both you may need to check the crankshaft position sensor (cps sensor) if your batery gate on your dashbord goes donw every time you crank it you may have a bad start motor. some time you may hear just a clic clic every time you crank and that is cused for stikin selenoid on the starter motor and you need to repe it.

Jun 05, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
2001 Ford Ranger Regular Cab Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...