Question about Chrysler Cars & Trucks

Open Question

Diagram were oil sensor location no chrysler 300 2.7engine

Oil light comes on an oil level is fine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

Ad
  • 55 Answers

SOURCE: Oil sensor

The oil light on your car has nothing to do with oil level in the crankcase but rather oil pressure. The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you have engine noise or suspect low oil pressure, I'd replace it but you could check oil pressure for peace of mind with an pressure gauge if you wish. You may need a special socket to replace it.

Posted on Oct 18, 2008

  • 1 Answer

SOURCE: Oil pressure sensor light comes on and oil level is fine

This is probably an oil pressure sensor problem.  Randomly going from 0 to over 130 is means the sensor is putting out out of range signals.  Mine would even read --- at times.  I told the mechanic to not spend any time troubleshooting just change the sensor.  $121 including parts, labor and tax.  The gage should read about 70 psi plus or minus several psi, and move up a PSI or two as you rev up the engine.  It took him about 10 minutes to change it, once he got the part.  There would have been a diagnostic charge of about $50, had I not been sure.

Posted on Apr 13, 2009

  • 17 Answers

SOURCE: oil light comes on under deceleration.oil levels are fine

I would guess your oil pump is going out causing it to loose oil pressure. If you continue to drive your car in this condition it will most likely ruin the engine. If it is not your oil pump it is something else causing you to loose oil pressure and I would have it looked at soon.

Posted on May 23, 2009

garyatwell
  • 72 Answers

SOURCE: 19968 chrysler town and country- oil light stays

This could be caused by a faulty oil sending unit, wich is located on the intake manifold or near it

Posted on Nov 07, 2009

Testimonial: "Thanks for the help."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When the vehicle is stopped and ideling the oil light comes on


Oil level is low or the sensor is bad for oil level.

Apr 16, 2010 | 2001 Chrysler Sebring

2 Answers

Oil light comes on while at an stop sign and traffic light


Check the oil level, if the oi level is good. Then it's a good chance that the oil pressure sensor may have gone bad and needs to be replaced as long as there is no damaging noise coming from the engine.

It is very hard to try to reach the sensor from under the car. Removed the battery, air box, also moved the fuse box aside just a bit to get more room to work (not necessary though if you have long arms). After removing/moving those parts you'll have plenty of room to work with. Simply disconnect the electric connection and remove the sensor with a socket. The part is $11.99 at Auto Zone with a lifetime warranty! (not just a dealer only item :]) The socket isn't a special socket its just a 27mm deep well. I hope this helps someone, overall the job isn't hard so no need to pay anyone to do it for you! Good luck, the oil pressure sending unit located high on the back of the engine block.

Dec 23, 2009 | 2003 Chrysler PT Cruiser

2 Answers

19968 chrysler town and country- oil light stays on, oil level is fine.


This could be caused by a faulty oil sending unit, wich is located on the intake manifold or near it

Nov 07, 2009 | 1998 Chrysler Town & Country

2 Answers

Oil preasure light comes on


Your oil sensor may be faulty, or your may have a leak since you said the fluid level is okay.

Sep 23, 2009 | 2001 Chrysler Sebring

1 Answer

Oil light keeps coming on and dinging


Your oil sensor may be faulty, or your may have a leak since you said the fluid level is okay.

Sep 16, 2009 | 2001 Chrysler PT Cruiser

1 Answer

My wife says the oil light just came on her 2001 beetle (is this a low level sensor?)


oil pressure sensor = when oil light comes on = sensor is not recieving a high enough oil pressure. 1) Did you check the oil level in the engine? 2) if the oil level is fine, and it just had an oil change, the filter (filament style) might have been installed upside down. also does the light come on and beep only during first couyple seconds of being started or while driving down the road?

Jul 08, 2009 | 2001 Volkswagen Beetle

2 Answers

Oil pressure


Could be the oil pump going bad. The oil sensor registers oil pressure, not oil level. If it isn't pumping oil, the light will come on.

Jul 01, 2009 | 2000 Chrysler 300M

2 Answers

Oil pressure sensor light comes on and oil level is fine


This is probably an oil pressure sensor problem.  Randomly going from 0 to over 130 is means the sensor is putting out out of range signals.  Mine would even read --- at times.  I told the mechanic to not spend any time troubleshooting just change the sensor.  $121 including parts, labor and tax.  The gage should read about 70 psi plus or minus several psi, and move up a PSI or two as you rev up the engine.  It took him about 10 minutes to change it, once he got the part.  There would have been a diagnostic charge of about $50, had I not been sure.

Jan 14, 2009 | 2005 Buick LeSabre

1 Answer

Oil light on when car reaches operating temp then engine knocks


check oil type and u may have worm out rod bearing

Dec 07, 2008 | 2001 Chrysler Concorde

1 Answer

Oil sensor


The oil light on your car has nothing to do with oil level in the crankcase but rather oil pressure. The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you have engine noise or suspect low oil pressure, I'd replace it but you could check oil pressure for peace of mind with an pressure gauge if you wish. You may need a special socket to replace it.

Oct 18, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...